Kikusui KJM6710 Operation Manual Download Page 43 | Manualshive

Page: 43 / 60

Kikusui KJM6710 Operation Manual Download Page 43

KJM6710

RS-232C Control 4-11

(Example) Set the symmetry mode to AUT.

SYM:MOD AUT

Response message

Returns the current setting in response to SYM:MOD? in charac-
ters (AUT, OFFS, or MAN).

SYMMETRY:OFFSET:LEVEL (SYM:OFFS:LEV)

Sets the symmetry offset or slice level. Or, queries the current set-
ting.
This message is valid only when the symmetry mode is OFFSET

or MANUAL. The speci

fi

ed value is applied to the symmetry off-

set or slice level depending on the symmetry mode.

Program message

• Syntax

Command message:SYMMETRY:OFFSET

:LEVEL_<value>
SYM:OFFS:LEV_<value>

Query message:

SYMMETRY:OFFSET:LEVEL?
SYM:OFFS:LEV?

• Program data

Data format:

Integer

Values:

–128 to +127

Resolution:

1

(Example) Set the symmetry offset or slice level to 32.

SYM:OFFs:LEV 32

Response message

Returns the current setting in response to SYM:OFFS:LEV? in

integers (–128 to +127).

SYMMETRY:SLICE:LEVEL (SYM:SLIC:LEV)

Queries the symmetry slice level.
The amplitude of the input signal (100 %) corresponds to a slice

level value of approximately 600. Thus, the returned value is

between –300 and +300.

«
...
41
42
43
44
45
...
»

Summary of Contents for KJM6710





























































Reviews:

No comments