background image

6

3. Other Alarm Visual and Audible Indicators

Operational Mode

Visual Indications

Audible Indications

Action/Note:

normal (standby)

AC power: 

 Green LED on continuously 

during light conditions, or blink every 60 sec 
during dark conditions.  

DC power:

 Green LED blink approx every 60 sec.

test (button press when 

no alarm condition is 

present)

 4 patterns of Red/Amber/Green.

 Test: Red LED blinks in time with 

alarm pattern.

 Green LED fade on/off at test 

complete

• 

Button press sound

 Voice: "Testing, this is very loud. 

Press now to cancel test. 5, 4, 3, 2, 1."

 3 long beeps, Voice "Fire!", 3 long 

beeps, Voice "Test Complete," Power 

on/reset sound.

 Voice "Test Canceled" if button 

pushed before test sequence begins.

Perform Test/Hush® button 

press once a week to verify 

proper alarm operation

* Push/release button before 

the countdown ends to 

cancel test.

Smoke Alarm Memory 

(unit has experienced 

a smoke alarm event 

within the last hour)

Red and Amber LED alternate on 1 

sec, every 10 sec.

After button push: "Smoke previously 

detected" only on the initiating 

alarm unit.

Push test button to clear 

Alarm Memory.  NOTE: stan-

dard test sequence will follow. 

(Push/release button again to 

cancel test).

Smoke Alarm Hush® 

Mode, (SMArt Hush® 

cOntrOl)

Red LED blinks every 2 sec.

After button push:  "Hush® Mode Acti-

vated."  Smoke alarm pattern stops.

(If there is too much smoke to allow 

Hush®: Voice "Too Much Smoke, Alarm 

cannot be Hushed" Smoke alarm 

pattern continues.)

This feature is to be used 

only when a known alarm 

condition, such as smoke from 

cooking, activates the alarm.

Smoke Alarm Hush® 

Mode canceled

None

Voice message "Hush® Mode 

Canceled."

When smoke levels drop 

below the alarm threshold, 

the voice message "Hush® 

Mode Canceled" will occur .

Initiating Alarm,

(Multiple alarms in an 

interconnected system)

Green LED blinks once per sec indicating 
that this is the unit initiating the alarm in an 
interconnected, multiple alarm, system.

Unit in smoke alarm mode.

During alarm, the initiating 

alarm red blink will be inter-

rupted by a green blink.

Summary of Contents for P4010ACS

























Reviews: