KI Unite System Assembly Instructions Manual Download | Manualshive

Page: 2 / 24

background image

2

Unite

®

Panel System - Table of Contents

Assembly Instructions

Rare Earth Magnets used with this product. The magnets can
be harmful to pacemaker wearers and others with medical
devices.

Pacemaker wearers should stay at least one

foot away from the steel tiles.

Unite

®

Panel System

Worksurface Installation:

Worksurface Bracket & Support Overview ..............................................3
Standard Cantilever Bracket Installation .................................................4
Edge Support Bracket with Lock .............................................................7
Design Bracket Installation .....................................................................8
Peninsula Surfaces with Add-On Peninsula Attachment Plate ...............9
Change-of-Height Bracket Overview ....................................................10
Corner Change-of-Height Brackets ......................................................11
Peninsula & Conference End Worksurfaces .........................................13
Worksurfaces to Panel-Mounted Support Leg ......................................15

Worksurface with Pedestal Support Installation:

Pedestal-to-Panel with Worksurface Installation ..................................17
Removing Drawers ...............................................................................17
Panel Support Bracket with and without Spacer Installation .................18
Typical Corner Intersection with Pedestal Support Installation .............19
Pedestal-to-Panel Installation ..............................................................19
Typical Return Peninsula with Pedestal Support Installation ................21
Typical Rectilinear Worksurface with Adjacent Worksurface and Pedestal
Support Installation ..............................................................................22

Worksurface with Gallery Panel Installation:

Gallery Panel Worksurface Edge Support Bracket Installation ..............23

«
1
2
3
4
...
»

Summary of Contents for Unite System

























Reviews:

No comments

Related manuals for Unite System

Brand: MANCHESTER WOOD Pages: 4

Brand: Officeworks Pages: 15

Brand: GAZZDA Pages: 2

Brand: Palram Pages: 8

Brand: Palram Pages: 18

Brand: Wallbeds Australia Pages: 3

Brand: GALA MEBLE Pages: 15

Brand: Habitat Pages: 7

Brand: woundwo Pages: 12

Brand: Landscape Forms Pages: 5

Brand: Bestar Pages: 16

Brand: Euro Style Pages: 6

Brand: Ameriwood HOME Pages: 38

Brand: Homebase Pages: 20

Brand: Armour Home Electronics Pages: 2

Traditional 4400-883-000

Brand: Stryker Pages: 2

Brand: Office Star Products Pages: 2

Brand: Happybeds Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands