4
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Doni
™
, Strive
®
,
Grazie
®
& Tandem Seating
Assembly Instructions
11. Orient the two assembled corner
table beams such that the beam
joint bottom bracket is face up
(upside-down for installation).
Position the two assembled corner
table beams into the remaining two
yokes of the corner table frame as
illustrated. Place a yoke plate onto
each beam and yoke of the corner
table frame, then insert and loosely
tighten four
5
/
16
-18 x 1” hex head
bolts and lock washers. Tightening
is not required at this time because
adjustment is required later
(Figure 2).
Corner Table Assembly
Note:
The corner table unit is first
assembled upside-down, and then
flipped right-side-up and attached
to the beam ends of two assembled
seating units.
Important:
The assembled corner
table unit
must
be installed to two
adjoining tandem units to form
a “U” or “L” configuration. The
assembled corner table unit
may
not
be installed as an end-of-run
table.
6. Carefully unpack all corner table
parts, set them out and identify all
components required for corner
table assembly (Figure 2).
7. Carefully set the 30” x 30” corner
tabletop side down onto a soft,
protective surface. Lay the corner
table frame assembly onto the table
and align the holes in the “yokes”
of the frame assembly with the
appropriate pre-drilled holes in
the underside of the corner table.
Secure the corner table frame
assembly to the corner table using
six #10 x
3
/
4
” Phillips screws.
Torque screws to 30 in/lb, taking
care to not over-tighten (Figure 2).
8. Take a corner table leg spacer in
hand, orient it so the plugged end
faces the back corner of the table
frame, then set the table leg spacer
into the back-corner yoke of the
frame. Place a corner table leg over
the spacer and yoke of the frame
then secure with four
5
/
16
-18 x 1”
hex head bolts and lock washers as
illustrated. Torque bolts to 21 ft/lb
in a diagonal pattern (Figure 2).
9. Locate a corner table beam and
position a beam joint top bracket
and beam joint bottom bracket over
the two mounting holes at one end
as illustrated. Insert two
5
/
16
-18 x 2
3
/
4
” through and secure
using two
5
/
16
-18” hex nuts
(Figure 2 & Detail A).
10. Repeat step 4 above for the second
corner table beam (Figure 2 &
Detail A).
30” x 30”
corner table
corner table
frame assembly
yoke
yoke
#10 x / ”
Phillips
screws
(13.0310)
3
4
yoke
plate
corner table
leg spacer
(plug end facing
back corner)
back corner
yoke
yoke
plate
beam joint
bottom
bracket
corner
table beam
beam joint
top bracket
beam joint
top bracket
beam joint
bottom
bracket
5
3
/ -18 x 2 / ”
hex head bolts
16
4
5
3
/ -18 x 2 / ”
hex head bolts
16
4
5
/ -18 x 1”
hex head
bolt &
lock washer
16
5
/ -18”
hex nuts
16
5
/ -18”
hex nuts
16
corner
table leg
Figure 2
5
/ -18 x 1”
hex head
bolt &
lock washer
16
5
/ -18 x 1”
hex head
bolt &
lock washer
16
corner
table beam
beam joint
bottom bracket
beam joint
top bracket
5
3
/ -18 x 2 / ”
hex head bolt
16
4
5
/ -18”
hex nut
16
Detail A
