manualshive.com logo in svg

Keysight N5244AU- H29, Installation Note, Page: 39 / 42

Share
Download
Keysight N5244AU- H29 Installation Note Download Page 39

 38                                                                                                                               Installation Note N5245-90109

Upgrade Kit Order Numbers: N5244AU-921 and N5245AU-921

-

Step 28.Perform Post-Upgrade Adjustments and Calibration

Adjustments

The following adjustments must be made due to the hardware changes of the 

analyzer.

— Default EE adjustment - select the LO Drive-NF adjustment and initialize 

the values.

— Source  adjustment
— Receiver adjustment
— Noise figure adjustment
These adjustments are described in the PNA Service Guide and in the PNA 

on-line HELP. A list of equipment required to perform these adjustments is also 

found in the service guide.
To view the Service Guide online, use the following steps:

1.

Go to

 www.keysight.com

2.

In the Search box, enter the model number of your analyzer, N5245A, and 

click 

Search

.

3.

Click 

Technical Support > Manuals

.

4.

Click 

Service Manual

.

5.

Click the service guide title to load the PDF file.

6.

When the PDF of the Service Guide is displayed, scroll through the 

Contents section bookmarks to locate the “Tests & Adjustments” chapter. 

After the specified adjustments have been performed, the analyzer should 

operate and phase lock over its entire frequency range. 

Operator’s Check

Perform the Operator’s Check to check the basic functionality of the analyzer. 

For instructions, refer to the “Tests & Adjustments” chapter of the Service 

Guide.
If you experience difficulty with the basic functioning of the analyzer, contact 

Keysight. Refer to 

“Contacting Keysight” on page 4

.

Calibration

Although the analyzer functions, its performance relative to its specifications 

has not been verified. It is recommended that a full instrument calibration be 

performed using the analyzer’s internal performance test software. Refer to the 

analyzer’s service guide for information on this performance test software.

Summary of Contents for N5244AU- H29











































Reviews:

No comments