manualshive.com logo in svg

Keysight N5244AU- H29, Installation Note, Page: 12 / 42

Share
Download
Keysight N5244AU- H29 Installation Note Download Page 12

Installation Note N5245-90109                                                                                                                                  11

Keysight Extended Power Range and Bias Tees 
Upgrade Kit Order Numbers: N5244AU-921 and N5245AU-921

-

Machine screw, M2.5 x 20, pan head 

4

0515-1992

-

Machine screw, M3.0 x 8, pan head 

3

0515-0372

-

Machine screw, M2.5 x 8, flat head 

2

0515-2487

W141

Adapter, straight 2.92 mm male-to-2.92 mm male, 50 ohm; 

 

A59 Noise Downconverter to A58 port 2 bridge

1

1250-3576

-

Inner cover (to replace existing inner cover)

1

N5247-00004

-

Mylar tape (applied to chassis in some older analyzers)

1

0460-0042

-

Cable tie

5

1400-0249

-

Dust cap for test port

4

1400-0214

Cables and Overlay (listed in the order in which they are installed)
Cables and Overlay  for Options 400/419/423 Only

 

Discard these three parts if you have Option H85 installed in the PNA.
W135

A56 port 1 noise bypass switch to A42 port 1 bias tee

1

N5245-20082

W137

A57 port 2 noise bypass switch to A45 port 2 bias tee 

1

N5245-20105

-

Lower 4-port front panel overlay

1

N5242-80012

Cables and Overlay  for Options 400/419/423/H85 Only

 

Discard these three parts if you do not have Option H85 installed in the PNA.
W125

A57 port 2 noise bypass switch to A36 test port 2 coupler

1

N5245-20138

W124

A56 port 1 noise bypass switch to A33 test port 1 coupler

1

N5245-20137

-

Lower 4-port front panel overlay

1

N5242-80019

Cables for Both Options 400/419/423  and 400/419/423/H85
-

Ribbon cable: A59 noise downconverter to A23 test set motherboard J550 

1

N5245-60013

W152

A59 noise downconverter J4 to A9 noise receiver board J9   

1

N5242-60041

W140

A57 port 2 noise bypass switch to A58 port 2 bridge arm

1

N5245-20107

W139

A57 port 2 noise bypass switch to A58 port 2 bridge thru 

1

N5245-20079

W136

A57 port 2 noise bypass switch to front-panel Port 2 CPLR THRU

1

N5245-20080

W134

A56 port 1 noise bypass switch to front-panel port 1 CPLR THRU

1

N5245-20084

W133

A56 port 1 noise bypass switch to front-panel port 1 SOURCE OUT

1

N5245-20083

W132

 A56 port 1 noise bypass switch to A38 port 1 source attenuator 

1

N5245-20081

W154

A59 noise downconverter to A28 mixer brick

1

N5245-20132

W151

A59 noise downconverter LO Out to A9 noise receiver board LO In

1

N5245-20133

W153

A59 noise downconverter RF Out to A9 noise receiver board RF In

1

N5245-20134

Table 1 

Contents of Upgrade Kit N5245-60109

Ref 

Desig.

Description

Qty

 Part Number

Summary of Contents for N5244AU- H29











































Reviews:

No comments