manualshive.com logo in svg

Keysight N4372E, User Manual

Share
Download
Keysight N4372E User Manual Download Page 74

74

Keysight N4372E Lightwave Component Analyzer User’s Guide

4

Making Measurements

a

If you want to use a different electrical calibration for the user 

calibration measurement and for the DUT measurement, "Electrical 

Calibration" can be used as the user calibration measurement in the 

"CalSet for User Calibration" combo box. 

This electrical calibration will only be used for the “user calibration” 

measurements. Afterwards the LCA returns to the currently 

activated electrical calibration for the DUT measurements.

The currently activated electrical calibration is preselected in the 

"CalSet for User Calibration" combo box. This preselection is fine 

and you have nothing to do if the same electrical calibration is used 

for the user calibration measurement and for the DUT measurement.

b

Select “Reduce IF-BW for user calibration measurement” to reduce 

noise on the user calibration data. The default bandwidth reduction 

factor is defined in the LCAConfig.xml file.

c

Click 

 to proceed.

d

Choose whether you want to save the calibration data for later use.

Summary of Contents for N4372E

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands