Keysight InfiniiVision M9241A Startup Manual Download Page 35

Page: 35 / 72

Keysight M9241/42/43A PXIe Oscilloscopes and M9240A AutoProbe Power Module

Startup Guide

7 Make a Measurement

Connect Probes to the Oscilloscope / 35
Input a Signal / 36
Using the Soft Front Panel (SFP) Interface / 36
Recall the Default Oscilloscope Setup / 37
Use Autoscale / 38
Compensate Passive Probes / 39
Turn On Measurements and Statistics / 40
Learn the Oscilloscope Display / 41

This chapter assumes you are using the Keysight InfiniiVision M924xA Soft Front

Panel (SFP). If you have not already opened the SFP, see

"Open the M924xA

Oscilloscope Soft Front Panel (SFP)"

on page 29.

Connect Probes to the Oscilloscope

Connect the oscilloscope probe to an oscilloscope channel BNC connector.

Connect the probe's retractable hook tip to the point of interest on the circuit or

device under test. Be sure to connect the probe ground lead to a ground point

on the circuit.

CAUTION

Maximum input voltage at analog inputs

135 Vrms
50

input: 5 Vrms Input protection is enabled in 50

mode and the 50

load will

disconnect if greater than 5 Vrms is detected. However the inputs could still be

damaged, depending on the time constant of the signal. The 50

input protection

only functions when the oscilloscope is powered on.

Summary of Contents for InfiniiVision M9241A









































































Search results

Summary of Contents for InfiniiVision M9241A

Reviews:

Related manuals for InfiniiVision M9241A

Brands by name

Popular brands

Keysight InfiniiVision M9241A, Startup Manual

Search results

Summary of Contents for InfiniiVision M9241A

Reviews:

Related manuals for InfiniiVision M9241A

Brands by name

Popular brands