background image

2

  

                                                                                                                            

  

Installation Note E8362-90004

Notice

THE MATERIAL CONTAINED IN THIS DOCUMENT IS PROVIDED “AS IS,” AND IS SUBJECT 
TO BEING CHANGED, WITHOUT NOTICE, IN FUTURE EDITIONS. FURTHER, TO THE 
MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, AGILENT DISCLAIMS ALL 
WARRANTIES, EITHER EXPRESS OR IMPLIED WITH REGARD TO THIS MANUAL AND ANY 
INFORMATION CONTAINED HEREIN, INCLUDING BUT NOT LIMITED TO THE IMPLIED 
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. 
AGILENT SHALL NOT BE LIABLE FOR ERRORS OR FOR INCIDENTAL 
OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH THE FURNISHING, USE, OR 
PERFORMANCE OF THIS DOCUMENT OR ANY INFORMATION CONTAINED HEREIN. 
SHOULD AGILENT AND THE USER HAVE A SEPARATE WRITTEN AGREEMENT WITH 
WARRANTY TERMS COVERING THE MATERIAL IN THIS DOCUMENT THAT CONFLICT 
WITH THESE TERMS, THE WARRANTY TERMS IN THE SEPARATE AGREEMENT WILL 
CONTROL.

Getting Assistance from Agilent

By internet, phone, or fax, get assistance with all your test and measurement needs.

Online assistance:

www.agilent.com/find/assist

United States

(tel)

 1 800 452 4844

Latin America

(tel)

 (305) 269 7500

(fax)

 (305) 269 7599

Canada

(tel)

 1 877 894 4414

(fax)

 (905) 282-6495

Europe

(tel)

 (+31) 20 547 2323

(fax)

 (+31) 20 547 2390

Australia

(tel)

 1 800 629 485

(fax) (+61) 3 9210 5947

New

 

Zealand

(tel)

 0 800 738 378

(fax)

 (+64) 4 495 8950

Japan

(tel) (+81) 426 56 7832
(fax) (+81) 426 56 7840

Singapore

(tel)

 1 800 375 8100

(fax)

 (65) 836 0252

Malaysia

(tel) 

1 800 828 848

(fax)

 1 800 801 664

India

(tel)

 1 600 11 2929

(fax)

 000 800 650 1101

Hong Kong

(tel) 

800 930 871

(fax)

 (852) 2506 9233

Taiwan

(tel

) 0800 047 866

(fax)

 (886) 2 25456723

Philippines

(tel

) (632) 8426802

(tel) (PLDT subscriber only)

1 800 16510170

(fax)

 (632) 8426809

(fax) (PLDT subscriber only)

1 800 16510288 

Thailand

(tel) (outside Bangkok)

(088) 226 008

(tel) (within Bangkok)

(662) 661 3999

(fax)

 (66) 1 661 3714

People’s Republic of China

(tel) (preferred)

800 810 0189

(tel) (alternate

)

10800 650 0021

(fax)

 10800 650 0121

Summary of Contents for E8362-60109































Reviews: