manualshive.com logo in svg

Keysight E8362-60109, Installation Note

Share
Download
Keysight E8362-60109 Installation Note Download Page 29

Installation Note E8362-90004                                                                                                                         

 

29

Step 17. Verify that the New Model Number Is Shown Correctly

Procedure Requirements

• The analyzer must be powered up and operating to perform this procedure.

• The Network Analyzer program must be running.

• A mouse is recommended for this procedure but is not required.

Mouse Procedure

1. On the analyzer’s 

Help

 menu, click 

About Network Analyzer

.

2. Verify that the new model number, E8363B, is shown correctly in the display. Click 

OK

.

3. On the analyzer front panel, press 

Preset

. Verify that the full frequency range of the 

analyzer is correct. The analyzer should preset to a frequency range of 10 MHz to 40 GHz.

Front Panel Keys Procedure

1. In the 

COMMAND

 block, press 

Menu/Dialog

.

2. In the 

NAVIGATION

 block, press the right tab and arrow keys to move over to the 

Help

 

menu, and down to the 

About Network Analyzer

 selection. Press 

Click

.

3. Verify that the new model number, E8363B, is shown correctly, then press 

Click

.

4. On the analyzer front panel, press 

Preset

. Verify that the full frequency range of the 

analyzer is correct. The analyzer should preset to a frequency range of 10 MHz to 40 GHz.

Summary of Contents for E8362-60109































Reviews:

No comments

Brands by name

Popular brands

Load more brands