Keysight E6961A User Manual And Method Of Implementation Download Page 72

Page: 72 / 75

Using the E6960-66600 Frequency Divider Board

Keysight E6961A User Guide and Method of Implementation

Switch B

Switch B sets the frequency divider to the relevant setting.

Note: Other combinations are not valid. if no valid switch setting is detected, LED

will flash indicating invalid switch B configuration. After reset, if no valid position

is detected, the board uses the “Free Run Mode” which generates an accurate 10

MHz signal.

off NA

on NA

Table D-1

Switch Operating Modes

Switches

Position

Operating mode

Comment

Table D-2

Switch B Operating Modes

Divider

Comment

To obtain 10 MHz output:

off

Not valid (def)

Free Run Mode

off

Div 1

Targeted 10MHz input clock

off

Div 5/2

Targeted 25MHz input clock

off off on off off off off off Div

20/3

Targeted

66.67MHz

input

clock

off off off on

off

Div 25/2

Targeted 125MHz input clock

off off off off on

off

Div 75

Targeted 750MHz input clock

Summary of Contents for E6961A












































































Search results

Summary of Contents for E6961A

Reviews:

Related manuals for E6961A

Brands by name

Popular brands

Keysight E6961A, User Manual And Method Of Implementation

Search results

Summary of Contents for E6961A

Reviews:

Related manuals for E6961A

Brands by name

Popular brands