Keysight DSOX3012T User Manual Download Page 395

Page: 395 / 530

395

Keysight InfiniiVision 3000T X-Series Oscilloscopes

User's Guide

25 CAN/LIN Triggering and

Serial Decode

Setup for CAN/CAN FD Signals / 395
Loading and Displaying CAN Symbolic Data / 398
CAN/CAN FD Triggering / 399
CAN/CAN FD Serial Decode / 402
Setup for LIN Signals / 407
Loading and Displaying LIN Symbolic Data / 409
LIN Triggering / 409
LIN Serial Decode / 411

CAN/LIN triggering and serial decode requires the AUTO license that you can get

by purchasing the DSOXT3AUTO upgrade.

Setup for CAN/CAN FD Signals

Setup consists of connecting the oscilloscope to a CAN signal, using the Signals

Menu to specify the signal source, threshold voltage level, baud rate, and sample

point.

Connect the oscilloscope to a CAN signal that has a dominant-low polarity. If you

are connecting to the CAN signal using a differential probe, connect the probe's

positive lead to the dominant-low CAN signal and connect the negative lead to

the dominant-high CAN signal.

To set up the oscilloscope to capture CAN signals:

Press

[Serial]

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands