Keysight Technologies N5221BU-605 Installation Note Download Page 42

Page: 42 / 88

42 Installation Note N5222-90114

Installation Procedure for the Upgrade

Step 25. Install the Bulkhead Connectors in the Test Set Front Plate

Refer to

Figure 21

for this procedure. New parts are listed in

Table 2 on

page 11

1. Locate the bulkhead connectors you removed earlier from the 2-port test

set front plate of the PNA. Use these and the new bulkhead connectors

included in the kit for the remainder of this step.

2. From the back side of the test set front plate, insert a bulkhead connector

into a hole in the plate.

3. Install 1x washer and 1x nut. Hand tighten nut and ensure bulkhead

connector hexagon nut, on the back side of test set front plate, is aligned

to the test set subpanel hexagon indent.

4. Repeat previous two steps for the remaining bulkhead connectors.

5. Torque nuts, on the front side of test set front plate, to 21 in-lbs.

Figure 21

Bulkhead Connectors Installation (1250-3805 (x10))

Summary of Contents for N5221BU-605

























































































Search results

Summary of Contents for N5221BU-605

Reviews:

Related manuals for N5221BU-605

Brands by name

Popular brands

Keysight Technologies N5221BU-605, Installation Note

Search results

Summary of Contents for N5221BU-605

Reviews:

Related manuals for N5221BU-605

Brands by name

Popular brands