Keysight Technologies M9710A Configuration And Measurement Instructions Download Page 3

Page: 3 / 16

Introduction

M9710A Hardware Extension of 89600 VSA Software

Introduction

The 89600 VSA software (89601B) supports the Keysight M9710A High-Speed
Digitizer. This VSA measurement hardware configuration offers broadband vector
signal analyzer capabilities. The maximum analysis bandwidth is model dependent.

Model

Option

Maximum Span (Analysis Bandwidth)

M9710A

-SR4

1.953 GHz (2.5 GHz in interleaved mode)

The present document aims to describe how to configure and use VSA software with
Keysight High-Speed Digitizers.

For details about VSA 89600 software usage, please refer to

VSA software help

(http://rfmw.em.keysight.com/wireless/helpfiles/89600B/WebHelp/89600.htm)

The

Vector Signal Analysis Basics

application note gives detailed information about

VSA analysis theory

(http://cp.literature.agilent.com/litweb/pdf/5989-1121EN.pdf).

Summary of Contents for M9710A

















Search results

Summary of Contents for M9710A

Reviews:

Related manuals for M9710A

Brands by name

Popular brands

Keysight Technologies M9710A, Configuration And Measurement Instructions

Search results

Summary of Contents for M9710A

Reviews:

Related manuals for M9710A

Brands by name

Popular brands