Keysight Technologies E4981A Service Manual Download Page 69 | Manualshive

Page: 69 / 152

background image

Chapter 4

67

Troubleshooting

Performance test failure troubleshooting

4. T

roub

lesho

o

ting

Performance test failure troubleshooting

This section describes the adjustment and troubleshooting procedures used when the
E4981A fails the performance tests. If the performance of the instrument is critical for the
test limits and seems to be adjustable, perform first the adjustment(s) related to the failed
test. When the test result is far from the tolerance of the test or the performance is not
adjustable, isolate the faulty assembly in accordance with the "Performance tests failure
troubleshooting procedure".

Performance test failure troubleshooting

represents the relationships between the failed test and probable faulty

assembly. If the performance test failure cannot be removed by a proper adjustment,
replace the assembly shown in this table.

Note that this table lists some typical cases. There are possibilities that another assembly
may be faulty.

###: Most suspicious assembly

##: Suspicious assembly

#: Possible faulty assembly

Table 4-11

Performance test failure troubleshooting information

Test
Num.

First failed test

Probable faulty board
assembly

A31

A34

PPMC

1

Test Signal Frequency Accuracy Test

#

###

2

Test Signal Level Accuracy Test

#

###

3

Impedance Measurement Accuracy Test

#

###

«
...
67
68
69
70
71
...
»

Summary of Contents for E4981A

























































































































































Reviews:

No comments

Related manuals for E4981A

Brand: Unitech Pages: 18

Brand: PCB Piezotronics Pages: 15

Brand: LEM Pages: 33

Brand: Reed Instruments Pages: 14

KEITHLEY 4200-CVU-PWR

Brand: Tektronix Pages: 6

micro-TRI-gloss ?

Brand: BYK Pages: 174

Brand: SellEton Scales Pages: 30

Brand: Bogen Pages: 14

Brand: Kurzweil Pages: 12

IMI Sensors 66212ANZ2

Brand: PCB Piezotronics Pages: 6

Brand: SMPE Pages: 2

Brand: NARDA Pages: 60

Brand: Vaisala Pages: 96

Brand: Omega Pages: 12

Brand: Metrohm Pages: 163

Brand: Clas Ohlson Pages: 4

Brand: Masimo Pages: 52

Brand: Ytc Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands