SPECIFICATIONS
9
KEYANG
DD–1203L-2 DRIVER DRILL
EN
2) Drilling
• Set the torque adjustment ring to the drilling
position.
The switch has braking function. When you
release the switch, it brings the motor to a
sudden stop. Also, the surplus rotation will be
stopped. It is very convenient for fastening
screws in soft materials processed. The
drill spindle is locked when the switch is not
pressed.
If drill stalls, it is usually because it is
being overloaded or improperly used.
Release trigger immediately. Do not
click trigger on and off in an attempt to
start a stalled drill.
9. Automatic Spindle Lock
This makes quick and easy changing of the
tool in the drill chuck possible.
This makes quick and easy changing of the
tool in the drill chuck possible.
10. Battery Protection
When the battery is overheating due to
continuous operation, in order to protect the
battery performance will automatically shut off
the power.
8. Maintenance
Always keep tool and air vent clean for
safe work.
1. Changing Tool
Before you change the tool, you must
remove the battery from the body of the
electric drill or set the rotational
direction switch in lock position
(neutral position).
1) Mounting the Bit
• Pull the lock sleeve forward.
• Insert a screw driver bit into the tool holder to
the end and release the lock sleeve.
2) Removing the Bit
• Keep the lock sleeve pressed forward
while taking out the bit.
2. Environmental Protection
The tool and its accessories contain much
raw materials and plastics that can be recycled
after their life. Therefore, plastic parts are
indicated with their material types so that
they can be classified and recycled for each
material type.
Do not dispose of the battery with home
garbage or into the fire or river.
Take care not to short-circuit the terminal of
the battery. The short-circuit of the terminal
may cause a fire or explosion doing a
serious personal injury.
2. Charging process
1) Charging indication
Green Blinks : Before charging
Red Lights : While charging
Green Lights : Charging completed
Red Blink : Overheat standby
(Battery overheated)
Yellow Blinks : Charging impossible
2) If charging of the heated battery is attempted
immediately after it has been used or
charged, indicator blinks in red (overheat
standby). After the cooling, indication
changes to red glowing and charging begins.
3) This charger detects charging status of the
batery and always keeps the battery in full
charge state.
Use only the specified battery and battery
charger. Otherwise battery and charger can
be damaged by fire, explosion,charging
error or overheat.
Be sure to unplug the charger after finishing
the charging.
3. Installing and removing battery
1) Installing.
Set the rotational direction switch at center
position (locked state).
Insert the charged battery into the slot
below the handle until the battery securely
latched with a click.
2) Removing.
Push the battery button once and take it
out to remove it.
4. Charge state of the battery
Pulling the switch trigger will turn on the
battery level indicator for about 2 seconds.
1 = Battery 70 - 100% charged
2 = Battery 30 - 69% charged
3 = Battery less than 30% charged
4 = Battery flat of defective
(Blinking/Turn off)
Always set the rotational direction switch at
center position when inserting the battery
or changing, carrying or storing the tool.
Figure 4
Figure 5
Figure 6
L (Left rotation) : Counterclockwise direction
(for loosening of screw)
R (right rotation) : Clockwise direction
(for fastening of screw, drilling)
Neutral : Rotation lock (for changing the bit)
7. Adjusting the Speed
1) Press the switch
The power tool switch allows the speed to
be increased steplessly up to maximum.
2) Move the speed selector switch
1: Low speed, high torque
2: High speed, low torque
8. Torque setting
1)Screw work
Selection is feasible from among five setting
anges by force (torgue)
adjustment ring.
low setting range when working with small
screw or at soft working material.
high setting range when working with large
screw or at hard working material.
When the tool is reached at the set torque,
the overload clutch begins to work to keep
the tool in the desired torque. You should
set the desired torque in the practical work.
2) Drilling
Set the torque adjustment ring to the drilling
position.( )
The switch has braking function. When you
release the switch, it brings the motor to a
sudden stop. Also, the surplus rotation will
be stopped.
It is very convenient for fastening screws in
soft materials processed.
Do not change direction of rotation until
the power tool is at a stand still.
Reversing the rotation direction must be
done only when the tool is switched off.
Reversing the direction during operation
may damage the tool
6. Reversing the Rotation Direction
Pulling the switch trigger will turn on
the LED light
Figure 10
Figure 11
Figure 9
Figure 8
5. Work light
Figure 7
If drill stalls, it is usually because it is being
overloaded or improperly used. Release
trigger immediately. Do not click trigger on
and off in an attempt to start a stalled drill.
9. Automatic Spindle Lock
The drill spindle is locked when the switch is not
pressed.
This makes quick and easy changing of the tool
in the drill chuck possibble.
10. Battery Protection
When the battery is overheating due to
continuous operation, in order to protect the
battery performance will automatically shut off the
power.
The tool and its accessories contain much
raw materials and plastics that can be
recycled after their life. Therefore, plastic
parts are indicated with their material types so
that they can be classified and recycled for
each material type.
For power tool with type Y attachment: if the
replacement of the supple cord is necesary,
this has to be done by the manufactuer or his
agent in order to avod a safety hazard.
It is very dangerous for customers to
troubleshoot or repair the tool for themselves,
Contact the nearest A/S center (sales agency)
and request for a service
If the replacement of the supply cord is
necessary. this has to be done by the
manufacturer or his agent in order to avoid a
safety hazard.
1) Mounting the Bit
Pull the lock sleeve forward.
Insert a screw driver bit into the tool
holder to the end and release the lock
sleeve.
2) Removing the bit
Keep the lock sleeve pressed forward
while taking out the bit.
Maintenance
Examples of Application
Always keep tool and air ventage clean for
safe work.
The repair shall be requested to the
qualified electric speciailst.
1. Changing tool
2.Environmental Protection
4. Y attachment cord
3. What to do when the tool does not work normally
Before you change the tool, you must remove
the battery from the body of the electric drill or
set the rotational direction swith in lock position
(neutral position).
Do not dispose of the battery with home
garbage or into the fire or river.
Driver Bit
Driver Bit
Magnetic Set
Socket Bit
Power
Screwdriver Set
Drill Bit for
Woodwork
Drill Bit for
Woodwork
Hole Saw
Socket Adaptor
Socket Adaptor
Universal Joint
Socket
Chuck Adaptor
Drill Socket
CORDLESS
DRIVER
DRILL
Socket
3. What to do when the tool does not work
normally
For power tool with type Y attachment: if the
replacement of the supple cord is necessary,
this has to be done by the manufacture or his
agent in order to avoid a safety hazard. It is
very dangerous for customers to trouble shoot
or repair the tool for themselves, Contact the
nearest A/S centre (sales agency) and request
for a service.
The repair shall be requested to the
qualified electric specialist.
4. Y attachment cord
If the replacement of the supply cord is
necessary. This has to be done by the
manufacturer or his agent in order to avoid a
safety hazard.
9. Examples of Application
Take care not to short-circuit the terminal of
the battery. The short-circuit of the terminal
may cause a fire or explosion doing a
serious personal injury.
2. Charging process
1) Charging indication
Green Blinks : Before charging
Red Lights : While charging
Green Lights : Charging completed
Red Blink : Overheat standby
(Battery overheated)
Yellow Blinks : Charging impossible
2) If charging of the heated battery is attempted
immediately after it has been used or
charged, indicator blinks in red (overheat
standby). After the cooling, indication
changes to red glowing and charging begins.
3) This charger detects charging status of the
batery and always keeps the battery in full
charge state.
Use only the specified battery and battery
charger. Otherwise battery and charger can
be damaged by fire, explosion,charging
error or overheat.
Be sure to unplug the charger after finishing
the charging.
3. Installing and removing battery
1) Installing.
Set the rotational direction switch at center
position (locked state).
Insert the charged battery into the slot
below the handle until the battery securely
latched with a click.
2) Removing.
Push the battery button once and take it
out to remove it.
4. Charge state of the battery
Pulling the switch trigger will turn on the
battery level indicator for about 2 seconds.
1 = Battery 70 - 100% charged
2 = Battery 30 - 69% charged
3 = Battery less than 30% charged
4 = Battery flat of defective
(Blinking/Turn off)
Always set the rotational direction switch at
center position when inserting the battery
or changing, carrying or storing the tool.
Figure 4
Figure 5
Figure 6
L (Left rotation) : Counterclockwise direction
(for loosening of screw)
R (right rotation) : Clockwise direction
(for fastening of screw, drilling)
Neutral : Rotation lock (for changing the bit)
7. Adjusting the Speed
1) Press the switch
The power tool switch allows the speed to
be increased steplessly up to maximum.
2) Move the speed selector switch
1: Low speed, high torque
2: High speed, low torque
8. Torque setting
1)Screw work
Selection is feasible from among five setting
anges by force (torgue)
adjustment ring.
low setting range when working with small
screw or at soft working material.
high setting range when working with large
screw or at hard working material.
When the tool is reached at the set torque,
the overload clutch begins to work to keep
the tool in the desired torque. You should
set the desired torque in the practical work.
2) Drilling
Set the torque adjustment ring to the drilling
position.( )
The switch has braking function. When you
release the switch, it brings the motor to a
sudden stop. Also, the surplus rotation will
be stopped.
It is very convenient for fastening screws in
soft materials processed.
Do not change direction of rotation until
the power tool is at a stand still.
Reversing the rotation direction must be
done only when the tool is switched off.
Reversing the direction during operation
may damage the tool
6. Reversing the Rotation Direction
Pulling the switch trigger will turn on
the LED light
Figure 10
Figure 11
Figure 9
Figure 8
5. Work light
Figure 7
If drill stalls, it is usually because it is being
overloaded or improperly used. Release
trigger immediately. Do not click trigger on
and off in an attempt to start a stalled drill.
9. Automatic Spindle Lock
The drill spindle is locked when the switch is not
pressed.
This makes quick and easy changing of the tool
in the drill chuck possibble.
10. Battery Protection
When the battery is overheating due to
continuous operation, in order to protect the
battery performance will automatically shut off the
power.
The tool and its accessories contain much
raw materials and plastics that can be
recycled after their life. Therefore, plastic
parts are indicated with their material types so
that they can be classified and recycled for
each material type.
For power tool with type Y attachment: if the
replacement of the supple cord is necesary,
this has to be done by the manufactuer or his
agent in order to avod a safety hazard.
It is very dangerous for customers to
troubleshoot or repair the tool for themselves,
Contact the nearest A/S center (sales agency)
and request for a service
If the replacement of the supply cord is
necessary. this has to be done by the
manufacturer or his agent in order to avoid a
safety hazard.
1) Mounting the Bit
Pull the lock sleeve forward.
Insert a screw driver bit into the tool
holder to the end and release the lock
sleeve.
2) Removing the bit
Keep the lock sleeve pressed forward
while taking out the bit.
Maintenance
Examples of Application
Always keep tool and air ventage clean for
safe work.
The repair shall be requested to the
qualified electric speciailst.
1. Changing tool
2.Environmental Protection
4. Y attachment cord
3. What to do when the tool does not work normally
Before you change the tool, you must remove
the battery from the body of the electric drill or
set the rotational direction swith in lock position
(neutral position).
Do not dispose of the battery with home
garbage or into the fire or river.
Driver Bit
Driver Bit
Magnetic Set
Socket Bit
Power
Screwdriver Set
Drill Bit for
Woodwork
Drill Bit for
Woodwork
Hole Saw
Socket Adaptor
Socket Adaptor
Universal Joint
Socket
Chuck Adaptor
Drill Socket
CORDLESS
DRIVER
DRILL
Socket
CORDLESS DRIVER DRILL
(Li-ion Battery)
To reduce the risk of injury,
user must read instruction
manual
ORIGINAL INSTRUCTION MANUAL
EN
2011.12
823-2 Wonsi-dong, Danwon-gu, Ansan-shi, Kyonggi-do, KOREA
Tel : Int+82-31-490-3000 Fax : Int+82-31-490-3019
Disposal of Old Electrical & Electronic Equipment (Applicable in the European
Union and other European countries with separate collection systems)
This symbol on the product or on its packaging indicates that this product shall not be
treated as household waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic equipment. By ensuring
this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be
caused by inappropriate waste handling of this product. The recycling of materials
will help to conserve natural resources. For more detailed information about recycling
of this product, please contact your local city office, your household waste disposal
service or the shop where you purchased the product.
11
