background image

SB-593 Satellite Board

Unit 17 Park Farm Industrial Estate

01925-001 Rev. 1.2

Buntingford, Herts SG9 9AZ UK
TEL: 0870 444 7234  FAX: 0870 444 7240
Web: http://www.kerisystems.co.uk  E-mail: [email protected]

Page 3 of 16

SB-593

Quick S

tart Guide

2.0

Cable Requirements

two conductor, stranded, AWG 22 or a larger gauge for all input/output connections

NOTE: The Lock Output relay may require a heavier gauge of wire depending upon the current demands of the lock 
and the length of the lock wiring run.

3.0

When Installing Satellite Boards

DO

route cables in accessible areas for ease of maintenance

add transient suppression across electric devices attached to a satellite board output

use an isolation relay (Keri Systems P/N IRP-1) if attaching to a parking gate, a turnstile, or any application 
using a large electric motor

for a single door application, install the door's reader to the TB-5, "A" reader connection on the controller

for a two door application, install the primary door's reader to the TB-5, "A" reader connection on the 
controller and install the secondary door's reader to the TB-6, "B" reader connection on the controller

DO NOT

stretch or over-tension cables

route cables over sharp objects

let cables or wires get tangled

4.0

Jumper Setting

JP12 - Configures the Satellite Board (see Figure 2)

Jumper across JP12, pins 1 and 2, configures the Satellite board for general purpose inputs and outputs.

NO jumper across JP12 configures the Satellite board for second door control with additional inputs and 
outputs. When the Satellite board is configured for second door control, the primary door must be connected to 
the "A" reader (TB-5 on the PXL-500/PXL-510 controller board) and the secondary door must be connected to 
the "B" reader (TB-6 on the controller board).

Figure 2: Satellite Board Jumper Configuration (JP12)

Summary of Contents for SB-593

















Reviews: