Kenwood TS-480 User Manual Download Page 7 | Manualshive

Page: 7 / 59

background image

7

Focusing on HF

Raising power output and adding an antenna tuner are both moves in the right direction, but
limiting the transceiver to the HF bands when the mainstream nowadays is HF~V/UHF would
seem to be going against the tide of the times. Yet opting for the multi-band route inevitably leads
to larger dimensions and higher prices. In this genre, price is an important factor, so by limiting the
TS-480 to HF, we developed what is in fact a compact transceiver that stands apart from the
competition. The TS-480 is designed to ensure not only excellent TX performance but also
superior RX performance.

«
...
5
6
7
8
9
...
»

Summary of Contents for TS-480




























































Reviews:

No comments

Related manuals for TS-480

Brand: PAG Pages: 2

Brand: XIEGU Pages: 48

Brand: XIEGU Pages: 13

Brand: Harris Pages: 162

Brand: MAMAC SYSTEMS Pages: 2

Brand: aci Pages: 8

Brand: aci Pages: 4

Brand: Lectrosonics Pages: 16

Brand: Williams Sound Pages: 8

Brand: M-system Pages: 2

Brand: AVGear Pages: 16

Brand: Dittel Pages: 38

Brand: V2 Pages: 20

TWOMOBILE MK II

Brand: GAREX Pages: 18

Brand: Olson Technology Pages: 12

Brand: Marantz Pages: 133

AMG3782RN-DR-SF

Brand: AMG Pages: 12

Satlook Digital NIT

Brand: emitor Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands