TK-U100
(
V
)
6
REALIGNMENT /
模式组合
2. 手持对讲机电源打开时,可以立即进入用户模式。P C 发送
指令时,手持对讲机进入 PC 模式。
手持对讲机发送数据时,红色的 LED 点亮。
手持对讲机接收数据时,绿色的 LED 点亮。
注意 :
• 个人电脑保存的数据写入 EEPROM 时,必须与机型和类型相
符。
• 请勿在数据发送或接收期间按 [PTT] 键。
3-3. KPG-22/KPG-22A 说明
(PC 编程接口电缆 :选购件 )
将 手 持 对 讲 机 与 电 脑 相 连 需 要 K P G -22/22A。 该 电 缆 的
D-sub 连接器 (KPG-22 :25 针,KPG-22A :9 针 ) 盒具有将 RS-
232C 逻辑电平转换为 TTL 电平的电路。
K P G -22/22A 将手持对讲机的 S P / M I C 连接器连接到电脑的
RS-232C 串行端口。
3-4. KCT-53U 说明 (USB 适配器 :选购件 )
KCT-53U 是将 KPG-22A 连接到电脑 USB 端口的电缆。
使用 K C T -53U 时,请在电脑上安装附带的 C D - R O M ( 带有
驱动程序软件 )。K C T -53U 驱动程序在 W i n d o w s 2000, X P 或
Vista(32 位 ) 下运行。
3-5. FPU( 编程软件 ) 说明
FPU 是 CD-ROM 附带的用于手持对讲机的编程软件。该软件
在 PC 的 Windows XP、Vista 或 7 下运行。该光盘上的软件允
许用户通过编程接口电缆 (KPG-22/22A) 对手持对讲机进行编
程。
注意 :
初次设置服务单元的市场代码和机型 / 频率数据时,请使
用与市场相符的 FPU。若单元设置有误,将无法予以恢复。
下面列出的接收频率由于内部振荡器的谐波可能对信号接
收造成干扰。
输入在表格中没有列出的频率
编号
频率
(MHz)
编号
频率
(MHz)
1
152.69375
9
153.60500
2
152.69500
10
153.60625
3
152.70000
11
172.79375
4
152.70500
12
172.79500
5
152.70625
13
172.80000
6
153.59375
14
172.80500
7
153.59500
15
172.80625
8
153.60000
2. When the POWER is switched on, user mode can be en-
tered immediately. When the PC sends a command, the
transceiver enters PC mode.
When data is read from the transceiver, the red LED
lights.
When data is written to by the transceiver, the green LED
lights.
Note:
• The data stored in the personal computer must match
Model Name and Model Type when it is written into EE-
PROM.
• Do not press the [PTT] key during data transmission or
reception.
3-3. KPG-22/KPG-22A Description
(PC programming interface cable: Option)
The KPG-22/22A is required to interface the transceiver
with the computer. It has a circuit in its D-sub connector
(KPG-22: 25-pin, KPG-22A: 9-pin) case that converts the RS-
232C logic level to the TTL level.
The KPG-22/22A connects the SP/MIC connector of the
transceiver to the RS-232C serial port of the computer.
3-4. KCT-53U Description (USB adapter: Option)
The KCT-53U is a cable which connects the KPG-22A to a
USB port on a computer.
When using the KCT-53U, install the supplied CD-ROM
(with driver software) in the computer. The KCT-53U driver
runs under Windows 2000, XP or Vista (32-bit).
3-5. FPU (Programming Software) Description
The FPU is the programming software for the transceiver
supplied on a CD-ROM. This software runs under windows
XP, Vista or 7 on a PC. The software on this disk allows a
user to program the transceiver via Programming interface
cable (KPG-22/22A).
Note:
Use the FPU that matches the market when you fi rst set
the market code and model name/frequency data to the
service unit. The unit set by mistake cannot be restored.
Receive frequencies listed below may result in the inter-
ference of reception due to the harmonics of internal oscilla-
tors.
Enter a frequency not listed in the table.
No.
Frequency (MHz)
No.
Frequency (MHz)
1
152.69375
9
153.60500
2
152.69500
10
153.60625
3
152.70000
11
172.79375
4
152.70500
12
172.79500
5
152.70625
13
172.80000
6
153.59375
14
172.80500
7
153.59500
15
172.80625
8
153.60000
Summary of Contents for TK-U100
Page 44: ...TK U100 V 40 MEMO 笔记 ...