TK-3302
8
1. Frequency Confi guration
The receiver utilizes double conversion. The first IF is
38.85MHz and the second IF is 450kHz. The fi rst local oscil-
lator signal is supplied from the PLL circuit.
The PLL circuit in the transmitter generates the neces-
sary frequencies. Fig. 1 shows the frequencies.
ANT
TX/RX :
:
ANT
SW
RF
AMP
TX
AMP
RF
AMP
1st MIX
MCF
38.85MHz
CF
450kHz
IF
SYSTEM
AF
AMP
SP
RX:
.
PLL
VCO
MIC
AMP
MIC
TX:
@
38.4MHz
X3
multiply
TCXO 12.8MHz
Model
Type
q
w
e
TK-3302
E,T
440~470MHz
440~470MHz
401.15~
431.15MHz
TK-3302
E3
400~430MHz
400~430MHz
361.15~
391.15MHz
Fig. 1 Frequency confi guration
2. Receiver
The frequency confi guration of the receiver is shown in
Fig. 2.
ANT
ANT
SW
BPF
RCTV
RF AMP
Q204
MIXER
Q203
IF AMP
Q202
BPF
PCTV 1st Local
MCF
XF201
IC201
IF, MIX, DET
IC308
AQUA-L
Q2
X3 multiply
X1
TXCO
CF201
2nd Local
12.8MHz
AF VOL
IC309
AF PA
SP
Fig. 2 Receiver section
■
Front End (RF AMP)
The signal coming from the antenna passes through the
transmit/receive switching diode circuit, (D103, D104 and
D105) passes through a BPF (L213 and L212), and is ampli-
fi ed by the RF amplifi er (Q204).
CIRCUIT DESCRIPTION
The resulting signal passes through a BPF (L209, L207
and L206) and goes to the mixer. These BPFs are adjusted
by variable capacitors (D201, D202, D203, D204 and D205).
The input voltage to the variable capacitor is regulated by
voltage output from the MCU (IC306).
■
First Mixer
The signal from the front end is mixed with the fi rst local
oscillator signal generated in the PLL circuit by Q203 to pro-
duce a fi rst IF frequency of 38.85MHz.
The resulting signal passes through the XF201 MCF to
cut the adjacent spurious and provide the opitimun charac-
teristics, such as adjacent frequency selectivity.
■
IF Amplifi er Circuit
The fi rst IF signal is passed through a four-pole monolithic
crystal fi lter (XF201) to remove the adjacent channel signal.
The fi ltered fi rst IF signal is amplifi ed by the fi rst IF ampli-
fier (Q202) and then applied to the lF system IC (IC201).
The IF system IC provides a second mixer, limiting amplifi er,
quadrature detector and RSSI (Received Signal Strength In-
dicator). The second mixer mixes the fi rst IF signal with the
38.4MHz of the second local oscillator output (TCXO X1 and
Q2) and produces the second IF signal of 450kHz.
The second IF signal is passed through the ceramic fi lter
(CF201) to remove the adjacent channel signal. The fi ltered
second IF signal is amplified by the limiting amplifier and
demodulated by the quadrature detector with the ceramic
discriminator (CD201). The demodulated signal is routed to
the audio circuit.
■
Wide/Narrow Switching Circuit
Narrow and Wide settings can be made for each channel
by switching the demodulation level.
The WIDE (low level) and NARROW (high level) data is
output from IC306, pin 5. When a WIDE (low level) data is
received, Q201 turn on. When a NARROW (high level) data
is received, Q201 turn off.
Q201 turns on/off with the Wide/Narrow data and the
IC201 detector output level is switched to maintain a con-
stant output level during wide or narrow signals.
Q201
R209
R210
C209
CD201
QUAD IFOUT
IC201
FM IF SYSTEM
W/N
(IC306)
L : Wide
H: Narrow
AFOUT
Q202
5R
Fig. 3 Wide/Narrow switching circuit
