KENWOOD TH-D7 A/G
-----
Memory Programming
----
Program a Simplex Frequency
Step 1
-
Direct Keypad Freq Entry to VFO
1.
[VFO]
→
[A/B]
to select VFO A or B
Ө
Sub-band will auto select by entering freq.
VFO A=118 or 2M; VFO B= 2M or 70cm
2.
[VFO]
→
[ENT]
Use Keypad & enter 6 digits
Step 2
–
Save VFO Freq to Memory Channel
1.
[F]
→
[MR]
; Channel Num Blinks
Ө
“ ” indicates the current channel is empty; “
►
”is
displayed if the channel contains data.
2.
[UP/DWN]
to select desired memory channel
3.
[OK]
to save & exit
Step 3
–
Labeling (Naming) Memory Channels
1.
[F]
→
[9]
use keypad enter Name (8 characters)
2. Press
[OK]
twice to save & exit
Program a Standard Repeater Frequency
Step 1
-
Direct Keypad Freq Entry to VFO
1.
[VFO]
→
[A/B]
to select VFO A or B
Ө
Sub-band will auto select by entering freq.
VFO A=118 or 2M; VFO B= 2M or 70cm
2.
[VFO]
→
[ENT]
Use Keypad & enter 6 digits
Step 2
–
Program Repeater Offset direction (+/-)
Ө
Go to
Step 5
if Access Tone not required.
1.
[F]
→
[MHz]
“+” or”-“ appears to indicate which
offset direction.
Step 3
–
Activate Tone Function
(if Required)
1.
[F]
→
[1]
to switch the Tone function ON (or OFF)
Step 4
–
Select a Tone Frequency
(if Required)
1.
[F]
→
[2]
to select TONE FREQ
2.
[UP/DWN]
to select appropriate tone Frequency.
3.
[OK]
to save & exit
Step 5
–
Save VFO Freq to Memory Channel
1.
[F]
→
[MR]
; Channel Num Blinks
Ө
“ ” indicates the current channel is empty; “
►
”
indicates if the channel contains data.
2.
[UP/DWN]
to select desired memory channel
3.
[OK]
to save & exit
Step 6
–
Labeling (Naming) Memory Channels
1.
[F]
→
[9]
use keypad enter Name (8 characters)
2. Press
[OK]
twice to save & exit
-----
Basic Operations
----
Memory Channel Recall
[MR]
Memory recall (pg 13*)
Lockout Memory Channel
Select desired Memory channel
[F]
→
[0]
(pg 36*)
Clear Memory Channel
Select the desired Memory Channel
Switch OFF
[MR]+ POWER ON
Press
[ESC]
to cancel or
[MR]
to clear contents (pg 13*)
Clear Memory Channel
[VFO]
Select Freq & related data
[F]
→
[CALL]
to store (pg 30*)
Select Sub-Band
(pg 12*)
[VFO]
to select VFO mode then
[F]
→
[A/B]
(Band A TX 144-148 MHz
,
Sub-Band RX118-174 MHz
,
Band B
TX/RX 430-450 MHz
Sub-Band RX 400-480 MHz, 144-148
)
Display Channel Labels (Names) or frequency
[MN
f]
Memory Name to Freq (pg 29*)
Copy Memory Contents to VFO
Recall Desired Memory Channel
[F]
→
[VFO]
(pg 31*)
Checking Repeater Input Frequency (Reverse)
[REV]
Auto Simplex Check (pg 24*)
Automatic Simplex Check (ASC)
[REV] (1s)
to switch on. Inverse “R” displayed
Press
[REV]
to quit (pg 24*)
Setting Power Level
[F]
→
[MENU]
Adjust Power Output (pg 9*)
Channel Display
[A/B] + POWER ON
(pg 31*)
BACKLIGHT DISPLAY HOLD ON
[F]
→
[LAMP]
SELECT ON or OFF
Receiver Power Save-Sampling Rate
[MENU] 1-2-1 Select desired interval
Squelch Level Adjustment
[F]
→
[MONI]
Adjust Squelch (pg 8*)
Tone Freq ID
[F] [2] (1s)
Scans through all tone freq
Press
[OK]
(1s) to activate
Press
[ESC]
to quit (pg 25*)
Tone Freq ID
[F] [2] (1s)
Scans through all tone freq
Press
[OK] (1s)
to activate
Press
[ESC]
to quit (pg 25*)
Program CALL transmit Freq
Select the desired transmit freq
[F]
→
[PTT] + [CALL]
(pg 30*)
Partial or Full Reset
[F]+POWER ON
Scan Features
VFO
- All Tuneable Freq’s
[VFO] (1s)
Memory
-Freq’s in Memory
[MR] (1s)
MHz
-All Freq’s in 1 MHz range
[MHz] (1s)
Program
-Freq’s in Programmed Range
[A/B]
select Band
[VFO]
select lower limit
[F]
→
[MR]
L0-L9,
[OK]
Select upper limit
[F]
→
[MR]
U0-U9,
[OK]
CALL/VFO
-
[VFO
] select freq,
[CALL] (1s
)
CALL/Memory
-
[CALL] (1s)
CANCEL SCAN-
[ESC]
Scan [MENU] 1-5-2
Time
-Stops on Busy Freq 5 seconds then continue
Carrier
- Stops on Busy Freq 2 seconds then continues
Seek
- Stops on first busy freq
