Kenwood NX-1000 Series User Manual Download Page 9

Page: 9 / 86

INSTALLING THE CAP OVER THE SPEAKER/ MICROPHONE JACKS

Note:

◆

For the speaker/ microphone jack, waterproof performance is guaranteed by
securing the supplied cap. Waterproof performance will not be guaranteed by
connecting an optional speaker/ microphone, etc.

◆

Use the Phillips #1 screwdriver.

If you are not using an optional speaker/

microphone or headset, install the cap over the
speaker/ microphone jacks.

Secure the cap in place using the

attached screw.

Speaker/ microphone

jack cap

Screw

INSTALLING THE SPEAKER/ MICROPHONE OR HEADSET

Note:

◆

The transceiver is not fully water resistant when using a speaker/ microphone
or headset.

◆

Use the Phillips #1 screwdriver.

Insert the speaker/ microphone plugs into the

speaker/ microphone jacks of the transceiver.

Place the locking bracket over the speaker/

microphone plugs so that the locking tabs insert
into the transceiver grooves.

Secure the locking bracket in place using the

attached screw.

Speaker/ microphone

locking bracket

Screw

Summary of Contents for NX-1000 Series























































































Search results

Summary of Contents for NX-1000 Series

Reviews:

Related manuals for NX-1000 Series

Brands by name

Popular brands

Kenwood NX-1000 Series, User Manual

Search results

Summary of Contents for NX-1000 Series

Reviews:

Related manuals for NX-1000 Series

Brands by name

Popular brands