Kenwood NX-1000 Series User Manual Download Page 65

Page: 65 / 86

Keypad Auto PTT

This function allows you to send DTMF by pressing Keypad
without

PTT

switch.

• If DTMF Manual Dialing is Enabled, the DTMF Code is

sent by pressing the

[ 0 ]

[ 9 ]

[ ]

[ # ]

button.

• Press the

[ 0 ]

[ 9 ]

[ ]

[ # ]

button, send the DTMF

Code of the pressed button.

• When the button is release, the modulation of DTMF

Code will stop, but unmodulated transmission will

continue for the time set by DTMF Hold Time.

Status

Press the

[ 0 ]

[ 9 ]

button to enter the Status Mode and

keypad input state.

Short Message

Press the

[ 0 ]

[ 9 ]

button to enter the Short Message

Mode and keypad input state.

Individual

Press the

[ 0 ]

[ 9 ]

button to enter the Individual Call

Mode or Selcall Mode and keypad input state.

Indi

Status

Press the

[ 0 ]

[ 9 ]

button to enter the Individual Call

Mode or Selcall Mode and keypad input state.

• Similar to pressing the

button for

[Indi

Status]

, press the

[ S ]

button in Individual Call Mode to

enter the Status Mode.

Indi Short

Message

Press the

[ 0 ]

[ 9 ]

button to enter the Individual Call

Mode or Selcall Mode and keypad input state.

• Similar to pressing the

button for

[Indi Short

Message]

, press the

[ S ]

button in Individual Call Mode

to enter the Short Message Mode.

Group

Press the

[ 0 ]

[ 9 ]

button to enter the Group Call Mode or

Selcall Mode and keypad input state.

Group + Status

Press the

[ 0 ]

[ 9 ]

button to enter the Group Call Mode or

Selcall Mode and keypad input state.

• Similar to pressing the

button for

[Group + Status]

press the

[ S ]

button in Group Call Mode to enter the

Status Mode.

Group + Short

Message

Press the

[ 0 ]

[ 9 ]

button to enter the Group Call Mode or

Selcall Mode and keypad input state.

• Similar to pressing the

button for

[Group + Short

Message]

, press the

[ S ]

button in Group Call Mode to

enter the Short Message Mode.

Summary of Contents for NX-1000 Series























































































Search results

Summary of Contents for NX-1000 Series

Reviews:

Related manuals for NX-1000 Series

Brands by name

Popular brands

Kenwood NX-1000 Series, User Manual

Search results

Summary of Contents for NX-1000 Series

Reviews:

Related manuals for NX-1000 Series

Brands by name

Popular brands