Kenwood NX-1000 Series User Manual Download Page 46

Page: 46 / 86

OST List

[Analog]

Allows you to enter OST List mode.

PF Button:

Press and hold the programmed button to enter OST List Mode.

Menu Mode:

Select “OST LIST” and press the

[ S ]

button to enter OST List

Mode.

Press the

[ <B ]

and

[ C> ]

buttons to select the OST List.

Press the

[ S ]

button to confirm and exit mode.

Refer to “Operator Selectable Tone (OST)” {p.

OVCM (Open Voice Channel Mode)

[DMR]

Allows you to hear various voice calls (Individual Call, Group Call, Broadcast Call)
even if the received ID does not match.

PF Button:

Press the programmed button to change the OVCM On.

• Beep A (1 beep) sounds.

Press this button again to change the OVCM Off.

• Beep B (2 beeps) sounds.

Menu Mode:

Select “OVCM” in Menu Mode and press the

[ S ]

button to change the OVCM On

or Off.

Summary of Contents for NX-1000 Series























































































Search results

Summary of Contents for NX-1000 Series

Reviews:

Related manuals for NX-1000 Series

Brands by name

Popular brands

Kenwood NX-1000 Series, User Manual

Search results

Summary of Contents for NX-1000 Series

Reviews:

Related manuals for NX-1000 Series

Brands by name

Popular brands