15
KIV-700/BT900
■
BT mode test mode (KIV-BT900)
The internal LOOPBACK function is available only in the model with the built-in BT.
∗
After switching into the BT mode (BT SRC) with TEL, follow the next steps of operations:
[FAV]
∗
Press and hold this key
Press and hold this key: To enter the internal LOOPBACK mode
∗
Set 22 in the Volume value when the product enters the internal LOOPBACK mode.
• Image of display
I
L
_
l
a
n
r
e
t
n
E
L
A
N
R
E
T
X
n
O
_
p
o
o
Note:
After running the internal LOOPBACK function, always reset the unit.
If you re-run the internal LOOPBACK function without resetting the unit, then the normal operation of other BT
system cannot be guaranteed.
[SEARCH MODE]
∗
Press and hold this key
Press and hold this key: To transfer into the BT device search mode and to start device detection
∗
Press and hold [SEARCH MODE] key in the device search mode to exit from the device search mode.
• Operation
The device search operation completes its search operation once it has detected 1 device.
Press [Rotary] key brie
fl
y under the device-not-detected condition (i.e., when the “Unknown” in the next image is
being displayed) to re-run the search.
• Image of display
The search operation is running.
When a device is not yet detected.
S
g
n
i
h
c
r
a
e
U
n
w
o
n
k
n
When a device is detected. “
∗∗∗∗∗∗∗∗∗
” is the device name.
■
AUDIO adjust mode
y
Press [AUD] key brie
fl
y to transfer into the Audio & DSP adjustment mode.
y
Press [
∗
] and [AUD] key on the remote controller to transfer into the Audio & DSP adjustment mode.
y
The default setting for the DSP Set shall be Bypass.
y
Press [
] / [
] key or turn the encoder to adjust Fader to 3 stages (R15
↔
0
↔
F15). (Initial value is 0)
y
Press [
] / [
] key or turn the encoder to adjust Balance to 3 stages (L15
↔
0
↔
R15). (Initial value is 0)
Press
[
] / [
] key or turn the encoder to adjust Sub Woofer Level to 3 stages (-15
↔
0
↔
+15). (Initial value is OFF)
y
Press [
] / [
] key or turn the encoder to adjust Volume Offset (except for the internal AUX) to 2 stages (-8
↔
0). (Initial value
is OFF)
y
Press [
] / [
] key or turn the encoder to adjust Volume Offset (internal AUX) to 3 stages (-8
↔
0
↔
+8). (Initial value is OFF)
y
In the Test mode, setting items for DSP Set and 2ZONE ON/OFF are located at the
fi
rst and second positions.
The
fi
rst line of the list is DSP Set, and the second line is 2ZONE ON/OFF.
y
Except for the above 2 items, the sequence of order of UIs and items is same as the sequence in the normal mode (Product
speci
fi
cation). (Refer to the following APPENDIX for the sequence of order.)
y
When the source is STANDBY, the source is other than BT Mode or 2ZONE is OFF, switch between Bypass and Through by
pressing and holding [FAV] key for 1 second.
y
After transferring to AUX source, forcibly set DSP ON (Through setting) in DSP setting.
After transferring to other source than AUX source (except for STANDBY and BT Mode), forcibly set DSP OFF (Bypass set-
ting) in DSP setting.
∗
Note that because the DSP settings cannot be switched in the case of 2Zone ON the settings do not change even if the
source has been switched.
TEST MODE
