KDC-MP828/W7531/W7531Y/W8531
/W8531Y/X789/X8529/X889
13
●
How to enter the test mode
In order to enter the test mode, reset the unit while simulta-
neously pressing down [1] and [3] keys.
●
How to clear the test mode
The test mode is cleared in case of any of the following events:
resetting, momentary power down, Acc OFF, Power OFF and
removal of the panel.
●
Initial conditions of the test mode
• Source is STANDBY.
• Displays lights are all turned on.
• The volume is at –10dB (The display is 30).
• Loudness (LOUD) is OFF.
• CRSC is OFF, regardless of whether there are switching
functions or not.
• SYSTEM Q is NATURAL (=FLAT).
• BEEP will sound anytime with a less than 1 second push.
• Auxiliary (AUX) is ON.
• DISPLAY TYPE is TYPE D.
• The Multi-function Key System are source dependent sys-
tems. (TUNER
→
Preset, CD / CD-CH
→
Scan, etc.)
• Display of TUNER sources will be as follows :
European Models : Upper Display=PS/frequency, Middle
Display=spectrum analyzer, Lower Display=multi-function
Other Models : Upper Display=SNPS, Middle Display =spec-
trum analyzer, Lower Display=multi-function
• CD source display will be as follows :
All Models : Upper Display=P-TIME, Middle Display= spec-
trum analyzer, Lower Display=multi-function
• SWPRE is SUB WOOFER.
Conventionally, the PS display has been visually checked on
the production line. This will be replaced by a new processing.
The PS data will be received and the PS contents is to be
verified as “RDS_TEST”. When this is verified, the P-CON
terminal is forced to go OFF. (In this case, “ _ ” means blank.)
This will be a dedicated test mode processing.
On the P-CON, when power is turned off once and, then,
turned on again, (Power OFF
→
ON) the unit will be re-
started.
●
Special display when set to TUNER
When in TUNER mode, if any of the following displays appear,
there is an abnormality with the front end.
• “TNE2P_NG” : At production site, the E2PROM is still with
the default (unspecified) value, due to the fact that the front-
end being shipped without going through the adjustment
process.
• “TNCON_NG” : In this condition, the communication with
the front-end is not possible.
●
Forced switching of K3I
In TUNER FM mode, each time [6] key is pressed, the func-
tions move in the following cycle :
AUTO
→
forced WIDE
→
forced MIDDLE
→
force NARROW
→
AUTO
The initial condition is AUTO and the displays below will ap-
pear.
• AUTO : FMA
• Forced MIDDLE : FMM
• Forced WIDE : FMW
• Forced NARROW : FMN
●
CD receiver test mode specifications
• Jumps are made to the following tracks by pressing the
[
] key.
No. 9
→
No. 15
→
No. 10
→
No. 11
→
No. 12
→
No. 13
→
No. 22
→
No. 14
→
No. 9 (Returns to the beginning)
It must be noted, however, that when paying MP3 / WMA /
AAC disk, which contain 8 files or less, the first track and
the following tracks are played in order.
• When [
] key is pressed, it goes down by 1 track.
• When a CD is used as a source, by pressing [1] key for less
than 1 second, a jump to the Track No. 28 is made.
• When a CD is used as a source, by pressing [2] key for less
than 1 second, a jump to the Track No. 14 is made.
• When a CD is used as a source, by pressing [3] key for less
than 1 second, a display of CD mechanism model name
and its version is made. When the pressing of [3] key for
less than 1 second is made for the second time, the normal
display is resumed. (Time code display)
• When a CD is used as a source, by pressing [6] key for less
than 1 second, a jump to the Track No. 15 is made. At the
same time, the volume value is set to 25 (2V PRE) and 27
(5V PRE).
TEST MODE
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
