Kenwood DM-3090 Page 17 Service Manual Download

Page: 17 / 48

• Defect occurred successively 10 times during REC-PLAY.
• As a result of occurrence of defect during REC-PLAY the

recordable cluster became zero.

• Adress is unreadable. REC state connot be set for 20 seconds

although retry is repeated.

• The following judgement is made according to the channel

status of digital signal which was input from D-IN during REC-
PAUSE or REC-PLAY.
(1) Other than audio signal
(2) Other than signals of home-use appliances
(3) Copy NG due to inversion of copy bit in CD.

• The digital signal which was input from D-IN during REC-

PAUSE, REC-PLAY or CD FUNC playback caused the
following.
(1) PLL of digital IN was unlocked.
(2) Locking occurred in condition other than FS = 44.1 kHz

• There were no areas to record music or character

infomation.(music name, disc name, etc.) during REC-PLAY.

• When an attempt to start is made, recordable area does not

remain.

• ETNO > LTNO
• FTNO

≠

0 or 1

• UTOC recorded on disc could not be read.

• Start address > End address

• Any data of UTOC 0 to 4 looped.

• Nonaudio data was recorded in the track mode of currently

selected TNO.

• Data "MINI" of system ID which has been written in TOC with

ASCII code is not correct.

• The disc type written i TOC does not correcpond to pre/

mastered MD, recording MD and hybrid MD.

• When an attempt to set REC-PAUSE was made, there were no

recordable areas.

• An attempt to set REC-PAUSE or to start editing was made on

the playback-only disc.

• An attempt to record or edit was made on the record/playback

disc with its careless rease preventing tab being in rease
preventing state.

• An attempt was made t oedit the track which was write-

protected by information written in UTOC.

• Specific editing conditions were not satisfied.

• Owing to occurrence of some trouble internal temperature of

set (MD unit) rose excessively.

• Read data was not correct or data could not be read correctly.
• Trouble occurred during recording if music data, resulting in

EXPLANATION OF ERROR DISPLAY

Error display

Errors

Corrective action

Can't REC

Can't COPY

Din UNLOCK

TOC FULL

UTOC ERR R

UTOC ERR A

UTOC ERR L0~4

NOT AUDIO

? DISC

DISC FULL

PLAYBACK MD

PROTECTED

Can't EDIT

TEMP OVER

DISC ERR RD

• Check that the disc is free from flaw, dust

and fingerprint.
Check whether there is any black spot.
Check for disc disalignment and run-out.

• Check whether CD is copy-inhibited one.

(An exabple: CD-R)

• Check whether there is any abnormality

in the D-IN signal line.

• Replace the disc with a recording/

playback disc in which an area to register
UTOC remains.

• UTOC data is not normal. Replace the

disc with other disc.

• UTOC data is not normal. Replace the

disc with other disc.

• UTOC data is not normal. Replace the

disc with other disc.

• Select other TNO or replace the disc with

other disc.

• The loaded disc is not applicable.

Replace the disc, and check.

• Replace the disc with other recording disc

in which recording area remains.

• The loaded disc is a Playback-only disc.

Replace the disc with a recording disc.

• Return the careless erase preventing tab

to its initial position, and redo.

• The track on which an attempt to edit was

made is a write-protected track. Redo on
another track.

• The applied operation procedure is not

proper. Redo, applying the ocrrect
procedure.

• Check by troubleshooting.
• Check whether the ambient temperature

is too high.

• Data of TOC or UTOC is not normal or

disc las flaw. Replace the disc with other

record failure.

disc.

DM-3090

TROUBLE SHOOTING

DM-3090(K)

COVER

97.11.29

0:19

y [ W

Summary of Contents for DM-3090

















































Search results

Summary of Contents for DM-3090

Reviews:

Related manuals for DM-3090

Brands by name

Popular brands

Kenwood DM-3090, Service Manual

Search results

Summary of Contents for DM-3090

Reviews:

Related manuals for DM-3090

Brands by name

Popular brands