know your table top
can opener
Your Kenwood Can Opener can be
used to open a variety of domestic
can shapes and sizes. In addition the
CO606 incorporates a bottle opener
and a knife sharpening facility.
before using your Kenwood
appliance
●
Read these instructions carefully
and retain for future reference.
●
Remove all packaging and any
labels.
safety
●
Do not immerse appliance, cord or
plug in water or other liquid.
●
Never use a damaged appliance.
Get it checked or repaired: see
‘service and customer care’.
●
Unplug the appliance from the
mains supply
●
●
before cleaning
●
●
immediately after use.
●
This appliance is not intended for
use by persons (including children)
with reduced physical, sensory or
mental capabilities, or lack of
experience and knowledge, unless
they have been given supervision or
instruction concerning use of the
appliance by a person responsible
for their safety.
●
Children should be supervised to
ensure that they do not play with
the appliance.
●
Only use the appliance for its
intended domestic use. Kenwood
will not accept any liability if the
appliance is subject to improper
use, or failure to comply with these
instructions.
before plugging in
●
Make sure your electricity supply is
the same as the one shown on the
underside of your can opener.
Important – UK only
●
The wires in the cord are coloured
as follows:
Blue = Neutral, Brown = Live.
●
The appliance must be protected
by a 3A approved (BS1362) fuse.
Note:
●
For non-rewireable plugs the fuse
cover MUST be refitted when
replacing the fuse. If the fuse cover
is lost then the plug must not be
used until a replacement can be
obtained. The correct fuse cover is
identified by colour and a
replacement may be obtained from
your Kenwood Authorised Repairer
(see Service).
●
If a non-rewireable plug is cut off it
must be DESTROYED
IMMEDIATELY. An electric shock
hazard may arise if an unwanted
non-rewireable plug is inadvertently
inserted into a 13A socket outlet.
●
This appliance conforms to EC
directive 2004/108/EC on
Electromagnetic Compatibility and
EC regulation no. 1935/2004 of
27/10/2004 on materials intended
for contact with food.
key
햲
bottle opener
햳
drive wheel
햴
magnet
햵
lever
햶
cutter blade
햷
guide pin
햸
knife sharpener
햹
cord stowage
using your table top can
opener
1 Ensure that the lever is in position
with the magnet housing fully
located (Fig. 1 and 2).
2 Plug the appliance into the power
supply.
3 Lift the lever to the open position.
4 Hold the can with the top rim
resting under the metal guide pin
and the can resting on the drive
wheel (Fig. 3).
5 Press the lever lightly down to start
the motor. The self-starting blade
will then pierce the can and
commence cutting.
6 The can will be held fixed in position
with the magnet resting against the
lid. Large or wide cans may require
extra support from the user.
7 Once the can is open, the motor
will automatically stop, retaining the
can and lid safely in place.
8 To remove, lift the lever whilst
holding the can.
9 With the exception of aluminium
cans, the lid will be retained by the
magnet.
10 For tidiness, any unwanted length
of cord can be stowed inside the
appliance.
using the bottle opener
When opening tall bottles, the unit
should be used towards the edge
of a work top.
1 Position the bottle with the cap
under the front rim of the bottle
opener.
2 Push down the bottle to remove the
cap whilst steadying the unit with
one hand.
햲
햵
햷
햸
햹
햶
햳
햴
Fig. 1
Fig. 2
Fig. 3
