background image

3

INS

TALL

A

T

ION INS

T

R

UC

T

IONS

 

R

ev

ela

tion |  06.2018

Part 1. 

PRODUCT USE & INSTALL ATION OPTIONS

This floor may be installed:

•  On, above or below grade
•  With glue down or nail down installation
•  Over OSB, plywood or concrete subfloor

This floor may be installed over radiant heat if:

•  The specific product style is approved for use over radiant heat (certain species and styles
•  Are not approved)
•  The floor is installed with glue down installation
•  The system is an hydronic (hot water) heat system, or an electric system specifically designed for use with 

hardwood flooring (must be approved by Kentwood Technical Services)

•  The system has an exterior thermostat in addition to interior controls
•  The installation conforms to the conditions specified in the Special Instructions for Installation over Radiant 

Heat (available from your kentwoodfloors.com)

•  If approved heat sensors are not installed under the floor in accordance with the Kentwood ‘Special 

Instructions for Installations Over Radiant Heat Systems, Kentwood accepts no responsibility for any damage 

to the floor caused by a radiant heat system. Such damage is not covered by the product warranty.

KENTWOOD accepts no responsibility for any damage to the floor caused by a radiant heat 

system. Such damage is not covered by the product warranty.
This floor should 

NOT

 be installed in a bathroom, laundry room or any area that may experience 

elevated humidity (sauna, sunroom, etc) Such use will void the product warranty.
KENTWOOD floors are for indoor use only, in residential or light commercial applications. The use of a 

certified installer is recommended for all installations.
For Technical Assistance in Canada, please call: 

1-800-992-3163

 

For Technical Assistance in the USA, please call: 

1-800-851-3841

 

or email 

[email protected]

Summary of Contents for Revelation














Reviews: