background image

2

 

 
 
 
 
 
 
 
 

_________________________________________________________________________ 
 
 
FCC STATEMENT FOR USB SOLO 
 
 
NOTE: This equipment has been tested and found to comply with the limits for a 
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are 
designed to provide reasonable protection against harmful interference in a 
residential installation. This equipment generates, uses and can radiate radio 
frequency energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio communications. However, 
there is no guarantee that interference will not occur in a particular installation. 
If this equipment does cause harmful interference to radio or television reception, 
which can be determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more of the following 
measures: 
 
-- Reorient or relocate the receiving antenna. 
-- Increase the separation between the equipment and receiver. 
-- Connect the equipment into an outlet on a circuit different from that to which the  
    receiver is connected. 
-- Consult the dealer or an experienced radio/TV technician for help. 
 
______________________________________________________________________ 
 

Summary of Contents for USB SOLO





















Reviews: