KENT 92804 Owner'S Manual Download | Manualshive

Page: 43 / 60

background image

41

REAR DERAILLEUR ADJUSTMENT:
The Low Gear Adjustment Screw (A)

determines how far the rear derailleur

will travel toward the wheel of the bicycle,

while the High Gear Adjustment Screw (B)

determines how far the cage will travel

toward the frame.
1. Shift the rear shifter to the largest

number indicated, disconnect the rear

derailleur cable from the cable anchor

bolt and place the chain on the smallest

sprocket.

2. Adjust the High Gear Adjustment

Screw (B) so the chain and the smallest sprocket are lined up vertically. Remove any

slack in the cable by pulling it taut, then re-connect the cable and tighten the cable

anchor bolt securely.

3. Some derailleurs have an adjusting barrel. Use the adjusting barrel and turn clockwise to

move the derailleur outboard - away from the wheel - while turning it counter-clockwise

will direct the chain inboard - towards the wheel.

4. Shift the chain onto the largest sprocket; adjust the Low Gear Adjustment Screw (A) so

the chain and the largest cog are lined up vertically. If you are unable to get the chain

to the largest cog, turning the Low Gear Adjustment Screw (A) counter-clockwise will

enable the chain to move towards the wheel.

5. Shift through the gears ensuring each gear is achieved quietly and without hesitation.
NOTE: It may take several adjustments to achieve the desired positioning. Please refer to the

troubleshooting section for more assistance. Check to be sure how the components on your

bike function.

MAINTENANCE/REPAIR

Low Gear

Adjustment

Screw (A)

High Gear

Adjustment

Screw (B)

CAUTION: CALL CUSTOMER SERVICE AT 800-451-KENT OR

CONSULT A PROFESSIONAL BICYCLE MECHANIC WITH ANY

QUESTIONS ON REPAIRS OR MAINTENANCE.

«
...
41
42
43
44
45
...
»

Summary of Contents for 92804





























































Reviews:

No comments

Related manuals for 92804

Brand: Beta Pages: 61

HEADSHOK FATTY DLR80

Brand: Cannondale Pages: 4

Big Wheel Drift Trike

Brand: SFD Pages: 12

Brand: Bosch Pages: 299

Brand: Bosch Pages: 238

Brand: Bosch Pages: 79

ConnectModule BCM3100

Brand: Bosch Pages: 26

Brand: Bosch Pages: 51

Brand: Bosch Pages: 32

Brand: Bosch Pages: 52

Brand: Bosch Pages: 55

eBike ABS BAS100

Brand: Bosch Pages: 93

Brand: Bosch Pages: 10

Brand: RockShox Pages: 39

Brand: Rose electronics Pages: 2

Brand: Rose electronics Pages: 28

Folding bicycle

Brand: Ecosmo Pages: 28

Brand: Echowell Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands