background image

- FORM NO. 56041562 / Rainmaker

 C

INTRODUCTION

This manual will help you get the most from your 

Kent/Euroclean Rainmaker

TM

 C

.   Read thoroughly

before operating the machine.

NOTE: Bold numbers in parenthesis indicate an item illustrated on page 7.

This product is intended for commercial use only.

PARTS AND SERVICE

Repairs, when required, should be performed by your authorized Kent/Euroclean Service Center, who
employs factory-trained service personnel, and maintains an inventory of Kent/Euroclean original
replacement parts and accessories.
Call the Kent/Euroclean DEALER named below for parts or service.  Please specify the Model and
Serial Number when discussing your machine.

NAME PLATE

The Model and Serial Number of your machine are shown on the nameplate on the machine.  This
information is needed when ordering repair parts for the machine.  Use the space below to note the
Model and Serial Number of your machine for future reference.
MODEL : ________________________________________
SERIAL NUMBER : _____________________________________

UNCRATING

When the machine is delivered, carefully inspect the shipping carton and the machine for damage.  If
damage is evident, save the shipping carton so that it can be inspected.  Contact Kent/Euroclean
Customer Service Department immediately to file a freight damage claim.

DO NOT OPERATE THE MACHINE UNTIL YOU HAVE READ THIS SECTION.
IMPROPER USE  WILL VOID THE WARRANTY.

Always use a defoamer when foaming occurs to prevent vacuum motor damage.

Never use water above 140

°

 F (60

°

C).

Do not store outdoors. Avoid extremes in temperature.

Do not let the pump run dry. Turn the pump off and refill that tank when cleaning solution
gets low.

Use approved chemicals only. All chemicals should be mixed thoroughly.  Liquid
chemicals are recommended to prevent powder buildups. A pH between 6 and 9 is
advised.  The use of high alkaline detergents or strong acids will accelerate the wear of
the pump and seals, and will void the warranty.

All extension cords must have a rating of at least 12/3 (#12 cord). Extension cords should
be no longer than 50 feet.  Replace the plug immediately if the ground prong becomes
damaged or is broken off.

(Dealer, affix service sticker here)

Summary of Contents for Rainmaker C


























Reviews: