FORM NO. 56041468 - SelectVac
™
12DC -
9
J, K - DUST CUP AND BAG
The cloth bag and the dust cup play a very important role in the
efficiency of the vacuum cleaner. The cloth bag allows air to move
through the cleaner while it traps dirt inside the cloth bag and the dust
cup. When dirt particles cling to the cloth bag they can restrict airflow.
If air cannot pass through the cloth bag, no cleaning can take place
regardless of how powerful the unit. Some fine particles can restrict
airflow very quickly and will decrease performance even before the
dust cup appears to be full. For that reason, when vacuuming
powder, flour dust, or similar fine substances, it may be necessary to
turn off the cleaner and empty the dust cup more often.
NOTE:
Turn off the switch and unplug the electrical cord before
emptying the dust cup. Never operate the vacuum cleaner without
the dust cup latched in place.
1
Unhook the clip from the top of the cloth bag.
2
Shake the cloth bag to release dust clinging inside.
3
Release each latch, one on either side of the handle (lift up
on the bottom and pull the top forward).
4
Lift the lid, swing it up and outward.
5
Reach in, grasp the dust cup and pull it out of the support.
6
Empty contents in a suitable container. (If desired, the cup can
be washed in warm water using a mild soap solution. Be sure
the cup is completely dry before replacing.)
7
Place the cup into the support, swing the lid shut, and fasten
each latch.
8
Hook clip to top of bag (refer to item 1).
CLEAN UP AND STORAGE
Store the machine in a cool dry place. Wind the extension cord in a
circle and hang on the cord hooks provided on the machine. Be sure
not to wind the cord tighter than necessary.
Avoid prolonged exposure of machine to freezing temperatures
during storage or transporting.
MAINTENANCE
WARNING:
BEFORE ANY SERVICING TO AVOID POSSIBLE INJURY
OR ELECTRIC SHOCK, DISCONNECT THE POWER CORD
FROM THE ELECTRICAL OUTLET.
BRUSH ROLL BELT REPLACEMENT
CAUTION!
Belt and pulley become hot during normal use.
The belt should be checked regularly. Replace belt if it is
stretching, cracking or slipping.
Remove the bottom chrome plate by turning the two cam locks on
each side. Remove the worn belt from the drive motor pulley.
Remove the brush roll from the base, and slide off worn belt. Slip new
belt around brush roll and reinstall into machine. Install belt around
drive pulley with low side in groove. Be sure belt is installed correctly
or brush roll will turn backwards. Replace chrome cover.
NOTE: Be sure brush roll with offset belt drive is oriented correctly,
with the shorter length to the left. Arrows on brush roll end-caps
indicates the top of cap and shows installation direction. Cut away any
hair or thread wound around the brush roll or the belt pulley because
the buildup could cause the belt to rotate unevenly.
BRUSH STRIP REPLACEMENT
To replace, remove the bottom chrome plate by turning the two cam
locks on each side and remove brush roll from machine. Remove nuts
and end caps. Slide out worn brush strips and replace. Reassemble
brush roll and reinstall in machine.
NOTE:
Brush strips are different lengths. Arrows on brush roll end
caps indicates the top of cap and shows installation direction.
headlight replacement
Pry off the headlight lens. Press bulb into socket, turn and remove.
Install new bulb and replace lens. NOTE: Use 25 watt bulb only.
CARBON MOTOR BRUSHES
Have Kent check the carbon motor brushes once a year or after 500
operating hours.
IMPORTANT !
Motor damage from failure to service the carbon brushes is not
covered under warranty.
FAN SCROLL
If your machine has a clear fan scroll attached to the underside of the
base, this may be removed and cleaned. Remove the chrome plate
and brush roll belt from pulley. Remove the two screws on either side
of the clear scroll, press the cam locks outward and lift the scroll from
the base. Dirt should clear easily, though some scraping may be
needed.
Be sure the gasket is in place. Reinstall by placing the rear-end
between the rear wheels and seat firmly. Reinstall belt and chrome
plate.
