manualshive.com logo in svg

Kenmore 796.4102#90#, Service Manual

The Kenmore 796.4102#90# Service Manual is now available for download on our website. This comprehensive manual provides step-by-step instructions for troubleshooting and repairing your Kenmore appliance. Get the answers you need for free, simply visit manualshive.com to access this valuable resource.

Share
Download
background image

2

CONTENTS

1. SPECIFICATIONS ............................................................................................................... 3

2. FEATURES & TECHNICAL EXPLANATION ....................................................................... 4

3. PARTS IDENTIFICATION  ................................................................................................... 7

4. INSTALLATION AND TEST  ................................................................................................ 8

5. OPERATION ...................................................................................................................... 11

5-1. CONTROL PANEL FEATURES  ................................................................................. 11
5-2. CYCLE GUIDE ........................................................................................................... 13
5-3. CYCLE OPTIONS  ...................................................................................................... 15
5-4. SPECIAL FUNCTION  ................................................................................................ 16
5-5. EXPLANATION OF EACH PROCESS ....................................................................... 17

6. PROGRAM CHART  .......................................................................................................... 19

7. TEST MODE  ..................................................................................................................... 21

7-1. SAFETY CAUTION .................................................................................................... 21
7-2. LOAD TEST MODE  ................................................................................................... 21
7-3. HOW TO CHECK THE WATER LEVEL FREQUENCY  ............................................. 21

8. TROUBLESHOOTING ...................................................................................................... 22

8-1. SAFETY CAUTION .................................................................................................... 22
8-2. ERROR MODE SUMMARY  ...................................................................................... 22
8-3. TROUBLESHOOTING SUMMARY    ..........................................................................24
8-4. TROUBLESHOOTING WITH ERROR ....................................................................... 26
8-5. TROUBLESHOOTING ELSE ..................................................................................... 33

9. COMPONENT TESTING INFORMATION ........................................................................ 38

9-1. FILTER ASSEMBLY (LINE FILTER) .......................................................................... 38
9-2. DOOR LOOK SWITCH ASSEMBLY .......................................................................... 39
9-3. STATOR ASSEMBLY ................................................................................................. 41
9-4. PUMP MOTOR ASSEMBLY ...................................................................................... 44
9-5. INLET VALVE ASSEMBLY ......................................................................................... 45
9-6. HEATER ASSEMBLY ................................................................................................. 46
9-7. THERMISTOR ASSEMBLY ....................................................................................... 47

10. DISASSEMBLY INSTRUCTIONS .................................................................................... 50

11.EXPLODED VIEW  ............................................................................................................ 58

11-1. CABINET AND CONTROL PANEL ASSEMBLY ...................................................... 58
11-2. DRUM AND TUB ASSEMBLY .................................................................................. 59
11-3. DISPENSER ASSEMBLY ........................................................................................ 60

Summary of Contents for 796.4102#90#































































Reviews:

No comments

Related manuals for 796.4102#90#

Landa PHW Operator'S Manual preview
PHW
Brand: Landa Pages: 26
GE GUD27GSSJ1WW Installation Instructions Manual preview
GUD27GSSJ1WW
Brand: GE Pages: 36
Jenn-Air JDB1255AWB44 Parts List preview
JDB1255AWB44
Brand: Jenn-Air Pages: 14
VALBERG 14S44 D XAD929C Instructions For Use Manual preview
14S44 D XAD929C
Brand: VALBERG Pages: 180
NEFF V6540X0GB Installation And Operating Instructions Manual preview
V6540X0GB
Brand: NEFF Pages: 32
Landa ENG Series Operator'S Manual preview
ENG Series
Brand: Landa Pages: 36
Fagor EVOconcept CCO-120DCW Installation, Use And Maintenance Instructions preview
EVOconcept CCO-120DCW
Brand: Fagor Pages: 156
Gaggenau DF 260 Instruction Manual preview
DF 260
Brand: Gaggenau Pages: 52
Hotpoint Ariston AQUALTIS AQ9D 48 X Instructions For Installation And Use Manual preview
AQUALTIS AQ9D 48 X
Brand: Hotpoint Ariston Pages: 48
Erbauer ERB069PRW Owner'S Manual preview
ERB069PRW
Brand: Erbauer Pages: 20
Gaggenau GI230760 Care And Use Manual preview
GI230760
Brand: Gaggenau Pages: 112
Philco PDA 870 User Manual preview
PDA 870
Brand: Philco Pages: 112
SOGEDIS T0 Series Manual preview
T0 Series
Brand: SOGEDIS Pages: 16
Galanz GLDW09TS2A5A User Manual preview
GLDW09TS2A5A
Brand: Galanz Pages: 32
Ariston AQUALTIS AQ7L 25 I Instructions For Installation And Use Manual preview
AQUALTIS AQ7L 25 I
Brand: Ariston Pages: 36
Sammic GLASS-PRO Series User Manual preview
GLASS-PRO Series
Brand: Sammic Pages: 68
Eswood ES-220 Equipment Manual preview
ES-220
Brand: Eswood Pages: 13
Haier HW110-B14979EU1 User Manual preview
HW110-B14979EU1
Brand: Haier Pages: 108

Brands by name

Popular brands

Load more brands