Kenmore 66514165L120 Owner'S Manual Download

Page: 9 / 29

Other Parts Needed (not provided):

3/8" (9.5 mm) Compression x

3/4" (19 mm) Hose Fitting

with rubber seal and 90°

elbow (required to properly

connect household water line

to the dishwasher.)

Part no: W10685193

Household Wiring (Metallic)

Strain Relief

to fit 7/8"

(22 mm) hole (required to

properly secure household

wiring to the dishwasher

terminal box.)

Part no: 4396672
NOTE:

Use only UL Listed/

CSA Approved parts.

Optional Accessory Parts Available:

Moisture Barrier Tape
NOTE:

Moisture barrier tape

is an optional, added level

of protection if installing a

dishwasher under a wooden

countertop. Recommended

but not required for wooden

countertop.

Part no: 4396277

Side Panel Kit

For enclosing the side of the

dishwasher when installing it

at the end of your cabinetry

(Whirlpool part number varies

with color).

Call us at our toll-free number or visit the brand website listed in

the Quick Start Guide for accessory and part information.

First-Time Installations

Check local codes. Check existing electrical supply. See the

“Electrical Requirements” section. It is recommended that

electrical connections be made by a licensed electrical installer.

Additional Tools Needed:

Small tubing cutter

Wire stripper

Cordless drill

1/2" (12.7 mm), 3/4" (19 mm),

and 1

" (38 mm)

hole saw bits

Additional Parts Needed (not provided):

Copper Tubing

(3/8" O.D.

suggested) or Flexible

Braided Water Supply Line

Kit. Kit includes braided hose

and 3/8" compression x

3/4" hose fitting.

Part no: W10278635RP

Screw-Type Clamps

"- 2"

(38 mm - 50 mm) (3 maximum)

Optional-Longer Drain Hose

(Maximum length 12 ft (3.7 m)

NOTE:

Must meet AHAM/

IAPMO test standards, fit 1"

(25 mm) drain connection,

and be resistant to heat and

detergent.

Part no: W11381654

NOTE:

If using a flexible braided hose, replace inlet hose after

5 years to reduce the risk of hose failure. Record hose installation

or replacement dates on the hose for future reference.

NOTE:

Be sure to purchase only Whirlpool factory-certified

parts and accessories for your appliance. Your installation may

require additional parts. To order, refer to the contact information

referenced in your Quick Start Guide.

Summary of Contents for 66514165L120





























Search results

Summary of Contents for 66514165L120

Reviews:

Related manuals for 66514165L120

Brands by name

Popular brands

Kenmore 66514165L120, Owner'S Manual

Search results

Summary of Contents for 66514165L120

Reviews:

Related manuals for 66514165L120

Brands by name

Popular brands