Kenmore 66514165L120 Owner'S Manual Download

Page: 20 / 29

INSTALL DOOR HANDLE

(ON SOME MODELS)

IMPORTANT:

Do not scratch the front panel during this

procedure. If door panel has a protective film, peel film back past

the point of the handle studs before installing handle. Handle is

easiest to install while unit is on its back.
Remove the door handle and hex key from the packaging.

Setscrews are already installed in the handle. Place handle on

mounting studs with the setscrews facing down. Push the door

handle tightly against the door. Insert the short end of the hex key

into the setscrews. Tighten the setscrews 1/4 turn past snug.

Retain hex key with Installation Instructions.

PLACE DISHWASHER IN CABINET

WARNING

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.
Failure to do so can result in back or other injury.

26.

Stand dishwasher upright

Using two or more people, stand the dishwasher up.

NOTE:

Do not install kick plate until instructed to do so.

Dishwasher may fit tightly into cabinet opening. Do not remove

insulation blanket—the blanket reduces the sound level.

IMPORTANT:

Do not kink or pinch water line, drain hose, power

cord, or direct wire between dishwasher and cabinet. Remove

cardboard from under dishwasher (if used).

25.

Install door handle

Mounting stud

Setscrew

(in bottom

of handle)

Handle

Hex key

Install Foam Side Shields (on some models)

Install the foam side shields on both the right and left sides of

the dishwasher. There are three attachment points on each side.

■

Attachment 1: Locate the slit on the side shield and attach it

to the hook on the side of the dishwashwe. (See figure 1)

■

Attachment 2: Use the other slit on the side shield and

attach it to the hook on the front of the dishwasher. (See

figure 2)

■

Attachment 3: Align the rectangular hole in the side shield

with the toe panel screw hole. Insert the Toe Panel

Screw(see figure 3) and Loosely tighten it to hold it in place

until the Toe Panel is installed.

■

Tuck the lower ends of the side shields under the

dishwasher. (See fugures 4 and 5)

Figure: 1

Figure: 2

Figure: 3

Figure: 4

Figure: 5

Summary of Contents for 66514165L120





























Search results

Summary of Contents for 66514165L120

Reviews:

Related manuals for 66514165L120

Brands by name

Popular brands

Kenmore 66514165L120, Owner'S Manual

Search results

Summary of Contents for 66514165L120

Reviews:

Related manuals for 66514165L120

Brands by name

Popular brands