background image

3

OPERATION

W

arr

anty

Safety

Cleaning

Oper

ation

Installa

tion

Ser
vice P

ar

ts

Always turn the downdraft blower on before you begin cooking 

to establish an air flow in the kitchen. Let the blower run for a few 

minutes to clean the air after you turn the cooktop off. This will 

keep the whole kitchen cleaner and brighter.

CONTROLS

NOTE
For most convenient operation, set the blower to your favorite 

speed.  The  blower  will  come  on  to  this  speed  whenever  the 

activating switch is pressed and the air vent rises.

HEAT SENTRY

When chimney is UP and blower is ON (at any speed) or OFF:
If the exhaust temperature becomes higher than expected, the Heat 

Sentry mode will activate and increase the blower speed to HIGH.
Lowering the chimney will turn blower OFF - even if Heat Sentry 

is active.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PER-

SONS, OBSERVE THE FOLLOWING:

1.  Use this unit only in the manner intended by the manufacturer. If you 

have questions, contact the manufacturer at the address listed in the 

warranty.

2.  Before  servicing  or  cleaning  unit,  switch  power  off  at  service  panel 

and lock the service disconnecting means to prevent power from being 

switched on accidentally. When the service disconnecting means cannot 

be locked, securely fasten a prominent warning device, such as a tag, 

to the service panel.

3.  Installation  work  and  electrical  wiring  must  be  done  by  a  qualified 

person(s)  in  accordance  with  all  applicable  codes  and  standards, 

including fire-rated codes and standards.

4.  Sufficient  air  is  needed  for  proper  combustion  and  exhausting  of 

gases through the flue (chimney) of fuel burning equipment to prevent 

backdrafting. Follow the heating equipment manufacturer’s guideline and 

safety standards such as those published by the National Fire Protection 

Association (NFPA), and the American Society for Heating, Refrigeration 

and Air Conditioning Engineers (ASHRAE), and the local code authorities.

5.  When cutting or drilling into wall or ceiling, do not damage electrical 

wiring and other hidden utilities.

6.  Do not use this unit with an additional speed control device.

7.  Ducted fans must always be vented to the outdoors.

8.  To reduce the risk of fire, use only metal ductwork.

9.  Do not install this product with the activating switch directly behind a 

burner or element. Minimum distance between the switch and the edge 

of the burner should be 4 inches.

10.  Loose-fitting or hanging clothing should never be worn when operating 

this appliance. They may be ignited by burners/elements on cooktop.

11.  Children should not be left alone or unattended in the area where this 

appliance is in use.

12.  This unit must be grounded.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

1.  Never leave surface units unattended at high settings. Boilovers cause 

smoking and greasy spillovers that may ignite. Heat oils slowly on low 

or medium settings.

2.  Always  turn  hood  ON  when  cooking  at  high  heat  or  when  cooking 

flaming foods.

3.  Clean  ventilating  fans  frequently.  Grease  should  not  be  allowed  to 

accumulate on fan or filter.

4.  Use proper pan size. Always use cookware appropriate for the size of 

the surface element.

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A 

RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:*

1.  SMOTHER  FLAMES  with  a  close-fitting  lid,  cookie  sheet,  or  metal 

tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the 

flames  do  not  go  out  immediately,  EVACUATE  AND  CALL  THE  FIRE 

DEPARTMENT.

2.  NEVER PICK UP A FLAMING PAN - You may be burned.

3.  DO NOT USE WATER, including wet dishcloths or towels - a violent steam 

explosion will result.

4.  Use an extinguisher ONLY if:

A.  You know you have a Class ABC extinguisher and you already know 

how to operate it.

B.  The fire is small and contained in the area where it started.
C.  The fire department is being called.
D.  You can fight the fire with your back to an exit.

* Based on “Kitchen Firesafety Tips” published by NFPA.

CAUTION

1.  For general ventilating use only. Do not use to exhaust hazardous or 

explosive materials and vapors.

2.  To avoid motor bearing damage and noisy and/or unbalanced impellers, 

keep drywall spray, construction dust, etc. off power unit.

3.  Clean filters and grease-laden surfaces frequently.

4.  Do not repair or replace any part of this appliance unless specifically 

recommended in this manual. All other servicing should be done by a 

qualified technician.

5.  Please read specification label on product for further information and 

requirements.

SAFETY INSTRUCTIONS

 INTENDED FOR DOMESTIC COOKING ONLY

 

Turn the downdraft blower ON by pressing down on the activating 

switch. The air vent will rise.

The blower can be turned ON or OFF and its speed can be adjusted 

with the recessed knob on the right side of the air vent.

Turn the downdraft blower OFF by pressing the activating switch 

again. The air vent will go down and the blower will shut OFF.

Summary of Contents for 233.5996 Series

























Reviews: