background image

 

 

KENCO Kenlift

®

 Operation Manual 

 

 

Section X.

 

Warranty  

 

E.

 

Policy 

 

1.

 

KENCO Corporation (KENCO) warrants the KENCO Kenlift

®

 lifting device (not 

including pads or consumable items) sold by KENCO to be free from proven defects in 
material and workmanship for a period of six (6) months from the delivery date to the 
original customer. 

2.

 

Warranty is limited to replacement of parts and/or assemblies, which upon inspection by 
KENCO are deemed to be defective in material, workmanship, or both. 

3.

 

Warranty shall not extend to products that have been altered or repaired in any way 
without the express written consent of KENCO. 

4.

 

Warranty shall not extend to any product that has been misused, abused, or improperly 
applied or any defect resulting thereof. 

5.

 

Defects and corrosion that are the result of improper storage and/or maintenance are not 
warrantable. 

6.

 

Wear items such as Pads, Pins or Lifting bails etc. are not considered for warranty claims. 

 

F.

 

Disclaimer 

 

1.

 

THIS WARRANTY IS EXCLUSIVE AND IN LIEW OF ALL OTHER 
REPRESENTATIONS AND WARRANTIES EXPRESSED OR IMPLIED, AND 
KENCO EXPLICITLY DISCLAIMS AND EXCLUDES ANY IMPLIED WARRANTY 
OF MERCHANTABILITY FOR A PARTICULAR PURPOSE.  IN NO EVENT SHALL 
THE END USER BE ENTITLED TO ANY CONSEQUENTIAL, INCIDENTAL OR 
CONTINGENT DAMAGES OF ANY KIND ARISING OUT OF BREACH OF 
CONTRACT, WARRANTY (INCLUDING NEGLIGENCE AND STRICT 
LIABILITY) OR OTHER THEORIES OF LAW, WITH RESPECT TO PRODUCTS 
SOLD OR SERVICES RENDERED BY KENCO, OR ANY UNDERTAKINGS, ACTS 
OR OMISSIONS RELATING THERETO. 

 

 

Summary of Contents for Kenlift

















Reviews: