Kelvinator KSV80HRD Installation Manual Download Page 3

3

Safety

WARNING

caution

 The unit must only be installed by a qualified refrigeration 
mechanic and electrical work carried out by a qualified 
electrician according to AS/NZS3000 electrical installation 
standard and all local and national regulations, and in 
compliance with this manual.

 Before installation, please contact a qualified air conditioner 
installer. If the unit is not installed by a qaulified air conditioner 
installer, any resulting malfunction may not be covered by 
warranty.

 If the supply cord is damaged, it must be replaced by the 
manufacturer, its service agent or similarly qualified persons in 
order to avoid a hazard.

 The appliance must be positioned so that the plug or isolation 
switch is accessible.

 The temperature of refrigerant circuit will be high, please keep 
the electrical cable away from the copper tube.

  This appliance is not intended for use by persons (including 
children) with reduced physical, sensory or mental 
capabilities,or lack of experience and knowledge, unless they 
have been given supervision or instruction concerning use of 
the appliance by a person responsible for their safety.

 Children should be supervised to ensure that they do not play 
with the appliance.

WARNING

warning

Before obtaining access to terminals, all supply circuits must be 

disconnected.

Please read this installation manual and the user manual before 
installation and carefully store in a handy place for later reference. 
Inside you will find many helpful hints on how to install and test the 
air conditioner properly. 

Electrical work must be installed by a licensed electrician. Be sure 
to use the correct rating of the power plug and main circuit for the 
model to be installed.

Incorrect installation due to ignoring this instruction may cause 
harm or damage, which may not be covered under warranty.

Meanings of symbols used in this manual are shown below:

WARNING

warning

This symbol indicates information concerning your  

personal safety

WARNING

caution

This symbol indicates information on how to avoid damaging the 

appliance

TIPS & INFORMATION

 important

This symbol indicates tips and information about  

use of the appliance

ENVIRONMENTAL TIPS

 environment

This symbol indicates tips and information about economical and 

ecological use of the appliance

 This symbol indicates never to do this

 This symbol indicates always do this

Important safety instructions

Notice for installation

Summary of Contents for KSV80HRD

















Reviews: