Kelvinator Air Conditioning
operating the air conditioner 11
10 operating the air conditioner
Kelvinator Air Conditioning
Timer operation
1 CLOCK/TIMER button
Press the CLOCK/TIMER button, the current timer
setting is displayed alongside either the TIMER ON
or TIMER OFF indicator, and will flash.
2 TEMP/TIME button
Press to set the desired time.
Forward
Backward
Each time you push the button, the time moves forward
or backward by 10 minutes depending on which
direction you press. The time alters as quickly as you
press the button.
3 After setting the timer for TIMER ON and TIMER OFF,
check that the TIMER indicator on the display panel of
the indoor unit is illuminated.
4 Cancel button (CANCEL)
Press the CANCEL button to cancel the timer setting.
Preform steps 1, 2 and 3 to change the settings.
caution
When you select the timer operation, the remote control
automatically transmits the timer signal to the indoor unit at
the specified time.
Therefore, keep the remote control in a location from which it
can transmit the signal to the indoor unit properly.
The effective operation time set by remote control is limited
within 24 hours.
Examples of timer settings
Start
Off
6:00
Timer On
The TIMER ON feature is useful when you want the unit
to turn on automatically before you return home. The air
conditioner will automatically start operating at the set time.
IMPORTANT: The time will be registered within a 0.5
second period (after pressing the TEMP/TIME
button), so you should continue pressing the
button until the desired time is established.
Otherwise you must repeat the steps again.
Drying operation
Start
Ensure unit is plugged in and power is available.
The OPERATION indicator on the display panel of the indoor
unit starts flashing.
1 Mode select button (MODE)
Press to select DRY.
2 TEMP/TIME button
Push the "TEMP/TIME" button to set the desired
temperature.
3 ON/OFF button
Stop
When the remote control is off, push this button to start the
air conditioner.
ON/OFF button
Push this button again to stop the air conditioner.
Note: The fan speed cannot be adjusted when the unit is in
AUTO and DRY mode.
MODE
❄
1
2
3
4
• The fan speed will be automatically controlled under
dry operation.
• During the dry operation, if the room temperature is
lower than 10
O
C, the compressor stops operating and
restarts only when the room temperature is above 12
O
C.
Eco operation
When you push the ECO button on the remote control
during cooling, heating, or AUTO operation ,the air
conditioner will automatically increase (cooling) or decrease
(heating) the set temperature by 1
O
C per hour for the first two
hours, then hold steady for the next 5 hours, after that the
unit will stop operation. The fan speed will be automatically
controlled. This feature can maintain the most comfortable
temperature and save more energy for you.
AUTO operation
The air conditioner will control room temperature
automatically around the temperature point set by you.
If the AUTO mode is uncomfortable, you can select desired
conditions manually.
Cooling/Heating/Fan only operation
Start
Ensure unit is plugged in and power is available.
The OPERATION lamp on the display panel of the indoor unit
starts flashing.
1 Mode select button (MODE) Press to select COOL,
HEAT (Not applicable to cooling only models),
or FAN ONLY.
2 TEMP/TIME button
Set the desired temperature, the most comfortable
temperature is between 21
O
C/70
O
F to 28
O
C/84
O
F.
3 Fan speed button
Press to select "AUTO" "LOW", "MED" and "HIGH"
4 ON/OFF button
When the remote control is off, push this button to start
the air conditioner.
Stop
ON/OFF button
Push this button again to stop the air conditioner.
The FAN ONLY mode does not control temperature.
Therefore, perform only steps 1,3, and 4 to activate
this mode.
• Open angle of the horizontal louver should not be
set too small, as COOLING or HEATING performance
may be impaired due to a restricted air flow area.
• Do not operate unit with horizontal louver in
closed position.
• When the air conditioner is connected to power
(initial power), the horizontal louver may generate a
sound for 10 seconds, this is a normal operation.
How to operate the air conditioner
Automatic operation
When you set the air conditioner to AUTO mode, it will
automatically select cooling, heating (only for reverse
cycle models), or fan only operation depending on what
temperature you have selected and the room temperature.
Once you select the operating mode, the operating
conditions are saved in the unit's microcomputer memory.
Thereafter, the air conditioner will start operating under
the same conditions when you simply push the ON/OFF
button on the remote control.
Start
Ensure the unit is plugged in and power is available.
The OPERATION indicator on the display panel of the
indoor unit starts flashing.
1 Mode select button (MODE)
Press to select AUTO.
2 TEMP/TIME button
Set the desired temperature. Normally,
set it between 21
O
C/70
O
F to 28
O
C/84
O
F.
3 ON/OFF button
When the remote control is off, push this button to start
the air conditioner.
Stop
ON/OFF button
Push this button again to stop the air conditioner.
If the AUTO mode is uncomfortable, you can select the
desired conditions manually.
When you select the AUTO mode, you do not have to set the
fan speed. The fan speed will be automatically controlled.
MODE
❄
1
2
3
4
MODE
❄
1
2
3
4
1 hour
1 hour
1 hour
1 hour
Set
Temperature
Set
Temperature
1
1
Eco operation
1
1
Eco operation
7 hours timer off
7 hours timer off
1
2
3
4
5
6
7
8
9
10
8
11
AUTO
MODE
❄
