background image

11

Table of contents >>

BEFORE USING THE MACHINE

* IMPORTANT! 

Check and tighten all bolts, nuts and all connections and specially the 

clamp sleeve for the pulley

* Check knives/flails, make sure they are installed properly. Replace broken, cracked or worn 
knives / flails.
* Check all protective covers, protective devices. Remove any transport locking device.
* Lubricate the drive shaft and other lubrication points .

OPERATION

Only people who understand the safety information and instructions in this manual may op-

erate the equipment. Be alert and careful when working with the machine and only use the 

equipment or product in the manner described in this manual. When working with equipment 

that has moving parts, there is always the risk of injury. Be careful when working with equip-

ment equipped with hydraulic hoses ,oil under pressure can penetrate the skin. Seek medical 
attention immediately if this occurs.

 

Always work alone with the equipments that are defined 

as single purpose equipment. Never overload the implement. Respect the equipment’s dan-

ger zone.

Connecting the machine 

* Attach the machine onto the tractor’s rear three point.

* Connect the PTO shaft. Anchor the chain well.

* Connect hydraulic hoses to the tractor’s double- acting hydraulic outlet

* Ready for use.

CUTTING

* Check the area to be cut and remove objects and trash that can be caught and thrown 
away by the blades.
* The amount of grass to be cut determines the speed forward; Low speed usually gives the 
best results. It is best to cut grass when dry. Cutting wet grass can cause clogging, which 
leads to grass lumps behind the cutting unit. When cutting very high grass, raise the cutting 
level and cut the same surface twice - the second time with lower cutting level, allow at least 
24 hours between first and second cutting to allow the grass to dry out.
* Lower the cutting unit on the ground. Connect the PTO shaft so that the blades start to 
rotate.

Check clamp sleeve for the pulley. The bolts should be 

tightened at regular intervals.Tighten and check the 

belt tension if necessary.

Summary of Contents for 35-XKE280

































Reviews: