Kellfri 35-FDM160 Manual Download Page 30 | Manualshive

Page: 30 / 56

background image

30

Table of Contents >>

• Oil refilling.

Oil volume 0.4 L (transmission oil 80W-90)

• Checking oil level

• Interval:

change oil before first operation

,

then after every 300 hours of operation
or once per year

Drainage plug

Raise the machine for draining.

GEARBOX - OIL CHANGE/REFILLING

CHECK BELT TENSION REGULARLY
The belt should move 20 mm (10 mm on each side) under pressure.

Tightening nut.

Tightening bolt.

Locking nut.

Adjust belt tension

1. Loosen locking nut.

2. Turn the tightening bolt clockwise to tighten

the belt and anticlockwise to loosen the belt.

3. Tighten the locking nut after adjusting the belt.

Interval:

After one hour of operation

After five hours of operation

After every 20 hours of operation.

Thereafter, tighten the belt when required.

BELT

«
...
28
29
30
31
32
...
»

Summary of Contents for 35-FDM160

























































Reviews:

No comments

Related manuals for 35-FDM160

Brand: Rangevision Pages: 31

D-MAS HyperSat 2540

Brand: DanMedical Pages: 103

Brand: Patlite Pages: 28

Web Ankle Brace

Brand: Darco Pages: 2

Brand: Darkly Labs Pages: 13

Brand: DARAY Pages: 24

Body Armor Night Splint

Brand: Darco Pages: 2

Brand: LaboGene Pages: 59

Brand: XDP Recreation Pages: 40

Brand: Raymarine Pages: 124

Brand: Raymarine Pages: 192

Brand: Parker Pages: 64

Brand: Parker Pages: 40

Matrx Digital MDM

Brand: Parker Pages: 20

Brand: UNIS Pages: 16

Bathomatic Basic

Brand: Unique Automation Pages: 10

Brand: Additel Pages: 139

Brand: VelociRAX Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands