background image

Operating the instrument on an incorrect line voltage  

may cause damage to the instrument, possibly voiding the 

warranty.

The power cord supplied with the Series 2600B contains a 

separate protective earth (safety ground) wire for use with 

grounded outlets. When proper connections are made, 

the instrument chassis is connected to power-line ground 

through the ground wire in the power cord. In the event of a 

failure, not using a properly grounded protective earth and 

grounded outlet may result in personal injury or death due to 

electric shock.  

 

Do not replace detachable MAINS supply cords with 

inadequately rated cords. Failure to use properly rated cords 

may result in personal injury or death due to electric shock.

To keep users safe, always read and follow all safety warnings 

provided with each of the instruments in your system.

Install the instrument

You can use the 2600B on a bench or in a rack. See the 

instructions that came with your rack-mount kit if you are 

installing the 2600B in a rack.

Connect line power

The Series 2600B operates from a line voltage of 100 V to  

240 V at a frequency of 50 Hz or 60 Hz. Line voltage is 

automatically sensed (there are no switches to set). Make sure 

the operating voltage in your area is compatible.

Summary of Contents for SourceMeter 2600B Series



















Reviews: