manualshive.com logo in svg

Keith WALKING FLOOR KICD, Owner'S/Operator'S Manual

Share
Download
Keith WALKING FLOOR KICD Owner'S/Operator'S Manual Download Page 38

        

 

 

 

 

31 

DOC06387     Rev.  C

OWNER / OPERATOR MANUAL  

KICD - Container Drive

OWNER / OPERATOR MANUAL  

KICD - Container Drive

Cylinder rod pad

Lower cross-drive clamps

Upper threaded clamp

Detail A
Step #3

Detail A
Step #4

Cylinder Pack Installation

Step #1

If all three cross-drives were fully retracted to the rear, unload end of the trailer before removing the old cylinder pack, then the 
threaded rod pads should be in the correct positions for installation.  Skip to step #2.

If the cross-drives were not fully retracted before removing the old cylinder pack, then the (4) check valves, poppets and 

springs will need to be removed from the new cylinder pack prior to installation (see previous section regarding Check Valve 

Replacement).  This will relieve hydraulic pressure and allow the rods to be moved into the correct positions to properly engage 

the upper cross-drive threaded clamps.

74133

Step #3

Fully engage all of the threads 

(moving or rotating the rods if 

necessary to get proper thread 

alignment).  

10632601

Flats are provided on the rod 
ends for rotation purposes.

Reattach manifold mounting plate and torque 
bolts prior to installing onto drive.

Summary of Contents for WALKING FLOOR KICD









































Reviews:

No comments

Brands by name

Popular brands

Load more brands