manualshive.com logo in svg

Keith WALKING FLOOR KICD, Owner'S/Operator'S Manual

Share
Download
Keith WALKING FLOOR KICD Owner'S/Operator'S Manual Download Page 20

        

 

 

 

 

13 

DOC06387     Rev.  C

OWNER / OPERATOR MANUAL  

KICD - Container Drive

OWNER / OPERATOR MANUAL  

KICD - Container Drive

LOADING CYCLE

Pressure

Return

Blocked Return Oil

Standing Oil

Stage 1

Pressure in the front of all cylinders.

Control valve actuator sends pressure to close the control valve 
and open the restrictor valve in the rear manifold.  Cylinder #3 is 

open to return, causing it to move. (Load does not move.)

Blocked by check valves.

Note:

 Stage 1 requires more pressure than stage 4.

Stage 2

Pressure still in front of all cylinders.

Cylinder #3 completes its full stroke, opening the check valve, 
allowing the oil in cylinder #2 to escape, causing it to move. 

(Load does not move.)

Blocked by check valve.

Note:

 Stage 2 requires more pressure than stage 1.

Stage 3

Pressure still in front of all cylinders. 

Cylinder #2 completes its full stroke, opening the check valve, 
allowing the oil in cylinder #1 to escape to return, causing it to 

move. (Load does not move.)

Note:

 Stage 3 requires more pressure than stage 2.

Revised 2019-11-25 

DOC06209  Rev. B

Stage 4

Cylinder #1 completes its stroke, shifting the switching valve, which 
reverses pressure and return, transferring the pressure to the rear of 
all cylinders.
 
All cylinders are now open to return and move to the front of the 
trailer together, moving the load.

As the cylinders complete their stroke, cylinder #3 shifts the switching 
valve, which reverses pressure and return, transferring the pressure 
to the front of all cylinders again and the cycle starts over.

Note:

 Stage 4 requires less pressure than stages 1, 2, or 3.

Front

Rear

3           2            1

             2            1

3

Front

Rear

Front

Rear

                           1

3            2

Front

Rear

3           2           1

Return

Pressure

Return

Pressure

Return

Pressure

Return

Pressure

Check

Valves

Control Valve 

Open

Restrictor 

Valve Open

Restrictor Valve 
Open

Switching
Valve

Control
Valve

Control Valve 
Closed

Control Valve 

Open

Check

Valves

Restrictor 

Valve Open

Restrictor Valve 
Open

Switching
Valve

Control
Valve

Control Valve 
Closed

Control Valve 

Open

Check

Valves

Restrictor 

Valve Open

Restrictor Valve 
Open

Switching
Valve

Control
Valve

Control Valve 
Closed

Control Valve 

Open

Check

Valves

Restrictor 

Valve Open

Restrictor Valve 
Closed

Switching
Valve

Control
Valve

Control Valve 
Closed

View from Underneath Looking Up

Summary of Contents for WALKING FLOOR KICD









































Reviews:

No comments

Brands by name

Popular brands

Load more brands