background image

ASSEMBLY INSTRUCTIONS

3103XX

8-foot ceiling

3104XX

9-foot ceiling

3105XX

8-foot ceiling

3106XX

9-foot ceiling

Height clearance 

96 in  (2,439 mm)

 108 in (2,743 mm)

96 in  (2,439 mm)

 108 in (2,743 mm)

Footprint (DxW)

61 in x 71 in (1,550 mm x 1,804 mm)

93 in x 71 in (2,362 mm x 1,804 mm)

 Insert Platform 

configuration (DxW)

- not applicable -

98 in x 71 in (2,489 mm x 1,804 mm)

Olympic Lifting 
Insert Platform

configuration (DxW) 

138 in x 100 in (3,505 mm x 2,540 mm)

172 in x 100 in (4,369 mm x 2,540 mm)

Free Space 

around Equipment 

(recommended)

INSTALLATION REQUIREMENTS

Note to Installer: 

Be sure to leave Assembly Instructions with the customer.

Note to Customer: 

Keep Assembly Instructions for future reference.

Skill level: 

Professional installation is required by qualified personnel.

Product failure due to improper installation is not covered under warranty.

READ CAREFULLY. KEEP THESE INSTRUCTIONS.

KEISER CORPORATION

2470 S. Cherry Ave.
Fresno, CA 93706

CUSTOMER SUPPORT

If you have any questions regarding the 

Assembly Instructions

 

after reading this guide, contact Keiser Customer Support:

1 559 256 8000

[email protected]

keiser.com/support

315503_A

HALF RACK 

KEISER STRENGTH

Verify planned equipment location is

 a solid, level, and structurally sound surface and 

meets the following dimensions criteria:

MODELS:

3103XX 

8-foot ceiling 

3104XX 

9-foot ceiling

3103XX model

3105XX model

3105XX Long Base 

8-foot ceiling 

3106XX Long Base 

9-foot ceiling

72 inches

(1,829 mm)

Sides*

48 inches

(1,219 mm)

Front

12 inches

(305 mm)

Rear

*Multiple Racks may share side Free Space.

Summary of Contents for 3103XX





















Reviews: