background image

 
 
 

 

T-305E User Manual Version 3.5 |  2 

Legal Notices 

 

The copyright of this material belongs to Kehui International Ltd. No company or individual may 
extract, copy or translate in any way without the written permission of the copyright owner. 
Copyright infringement will be investigated. 
 
This product complies with the design requirements for environmental protection and personal 
safety.  
 
This product is a professional instrument specially designed for power cable faults. Please do not use 
it for any other purpose. The company assumes no responsibility or loss if it is used for other 
purposes.  
 
The safety regulations in this user manual should be strictly adhered to.  
 
The storage, use and disposal of the product should be in accordance with the product manual, 
relevant contracts or relevant laws and regulations. 
 

As part of Kehui’s continual product development t

his product is subject to design or technical 

changes without prior notice. When product improvement or technical changes occur, you can check 
the information through Kehui International Ltd. website http://www.kehui.com. 
 

Disclaimer: 

Every effort has been made to make this material complete, accurate, and up-to-date. In 

addition, changes are periodically added to the information herein; these changes will be 
incorporated into new editions of the publication. Kehui International Ltd reserves the right to make 
improvements and/or changes to the product(s) and/or the program(s) described in this document 
without notice, and shall not be responsible for any damages, including but not limited to 
consequential damages, caused by reliance on the material presented, including but not limited to 
typographical errors.   

NOTE: Windows is a registered trademark of Microsoft.

 

 
Revision history: 

Data version 

Revision date 

Revision reason 

Person 

3.0  

2019.05.01 

New block diagram and front panel added, 
final edit 

TonYip/DiaKib 

3.1  

2019.05.01 

New block diagram P8 

DiaKib 

3.2 

2020.02.10 

Clarified grounding and T-H200 operation 

BilKib 

3.3 

2021.03.17 

Updated technical data, more detail on 2048J 
version 

BilKib 

3.4 

2021.04.10 

Replacement of diagrams with photographs. 
Page numbering & Order codes 

BilKib/DiaKib 

3.5 

2021.07.16 

Layout change and additional instructions 
following customer feedback 

BilKib 

 
 
 
Document number: T305E_UM_V3.5_EN 

 

Summary of Contents for T-305E

























Reviews: