background image

INSTALLATION INSTRUCTIONS

Before starting on the installation of the stove, the following steps need to be fully completed:

The chimney:

Alternative 1 An existing chimney prepared for rear connection

Alternative 2 A newly installed chimney prepared for rear connection

Alternative 3 Preparation for a new top connection chimney

Outdoor air supply

 (if so required)

Floor plate

 (unless a floor plate or floor glass is to be installed afterwards)

Several operations have to be carried out before the stove is put into place.

1. Place the bottom plate on the floor. You 

should preferably fasten the plate with a cou

-

ple of screws. The stove's adjustment screws 

will fit into the pre-punched holes in the four 

corners of the plate. If outdoor air is to be 

connected from below, the cover plate on the 

bottom plate has to be removed and the 100 

- 63 mm reduction piece installed before the 

stove is put into place.

2. If the stove is to have a rear connection, 

the back plate must be removed. Loosen 

the two screws in the top corners. Incline the 

back plate so it can be lifted from the bottom 

guide groove. 

Loosen the cover plate via a bolt inside. The 

cover plate is then mounted loosely in the top 

connection sleeve, unless there is a hot plate 

(accessory), in which case the cover lid is 

superfluous.

After this, install the rear connection sleeve 

(delivered in the fittings box). For top connec

-

tion, this part is superfluous.

Break out the cover piece and replace the 

back plate.

- 9 -

COVER PLATE

COVER PLATE

BOLT INSIDE

CONNECTION SLEEVE

Summary of Contents for K800 Series

















Reviews: