Keba ServoOne Device Help Download Page 65

Page: 65 / 493

The TTL interface accepts various TTL signal types, which can be selected using

P 558[0] - ENC_CH1_TTL_SignalType:

(0)AF_B - A/B tracks (forward counting, X4 encoding) - AB

(1)AR_B - A/B tracks (reverse counting, X4 encoding) - AB_inv

(2)ABDFN - A: Clock (falling edge), B: Direction (1 = positive) - PulseDir

(3)ABDRP - A: Clock (rising edge), B: Direction (1 = negative) - PulseDir_inv

(4)reserved

A maximum interpolation period, in ms (milliseconds), can be configured for the TTL

interface using P 601[0] - ENC_CH1_Period. Within this context, Period is the

maximum time of “no activity” since the last TTL counter event:

Period = 0: Function disabled (default)

Period > 0 (=n ms): If no counter event is registered in n ms, the speed will be
set to 0.

Zero pulse

There is no parameter for activating the zero pulse evaluation here, as this

evaluation is controlled exclusively based on the homing mode (see Section

"Homing" on page 252). However, setting P 541[0] - ENC_CH1_NpTest to 1

provides a test mode that can be used during commissioning in order to be able to

activate the zero pulse evaluation even without homing. Scope signals 1014 and

1016 can be used to view a received zero pulse within this context. This test mode

must be disabled during normal operation (P 541[0] = 0).

Commutation

Motor operation with pure incremental encoders needs for the auto commutation

function to be enabled without fail. For details see Section "Synchronous motor auto

commutation" on page 158.

ID No.: 0842.26B.5-01 Date: 09.2020

ServoOne - Device Help

6 Encoder

6.5.5.1.2 TTL incremental encoder with SSI absolute value inter-
face

See Section "SinCos incremental encoders with absolute value interface" on page

66 and in specialSection "SSI absolute value interface" on page 68.

Index Name

Unit Description

505

ENC_CH1_Sel = 3

Encoder selection set to TTL(3)

510

ENC_CH1_Num

Encoder gearing: Numerator

511

ENC_CH1_Denom

Encoder gearing: Denominator

540

ENC_CH1_Abs

Selection of absolute value interface

541

ENC_CH1_NpTest

ENC CH1, TEST-MODE: Index pulse signal(s) to Scope

542

ENC_CH1_lines

Number of lines (Sin/Cos / TTL encoders)

558

ENC_CH1_TTL_SignalType

Channel 1: TTL signal selection

601

ENC_CH1_Period

Maximum period of interpolation (TTL encoder)

616

ENC_CH1_CycleCount

Sampling cycle in: n x 125 μ (microseconds)

Table 6.9: Parameters for Channel 1 (X7) - TTL encoder

Summary of Contents for ServoOne














































































































































































































































































































































































































































































































Search results

Summary of Contents for ServoOne

Reviews:

Keba ServoOne, Device Help, Page: 65 / 493

Search results

Summary of Contents for ServoOne

Reviews: