Keating Of Chicago MIRACLEAN Service & Preventative Maintenance Training Download Page 27 | Manualshive

Page: 27 / 63

background image

25

Lighting Problems Trouble Shooting

• #2

- Defective thermostat

– With all components in “ON” position, clip a jumper wire
between the terminals on the thermostat. If the burner
ignites, replace the thermostat.

• #3

- Defective switch

– With all components in “ON” position, clip a jumper
   wire between the terminals on the switch on the side
   with the wire harness attached. If the burner ignites,
   replace the switch.

Note:

if there is continuity between

   the unused terminals on the switch, the wire harness
   could be moved to that side of the switch and could
   resolve a switch issue.

PROBLEM:

Pilot lights, burner does not

«
...
25
26
27
28
29
...
»

Summary of Contents for MIRACLEAN
































































Reviews:

No comments

Related manuals for MIRACLEAN

Brand: Southbend Pages: 80

Brand: BRABURA Griddle Pages: 24

Brand: Twin Eagles Pages: 24

Brand: Black Stone Pages: 51

Electric with Warming Tray

Brand: Oster Pages: 10

Brand: Oster Pages: 10

Brand: Oster Pages: 10

Brand: Oster Pages: 10

Brand: U.S. Range Pages: 2

Brand: STOK Pages: 2

Brand: croydon Pages: 2

Brand: PARRY Pages: 18

Brand: APW Wyott Pages: 24

Brand: Wells Pages: 40

Brand: Wells Pages: 18

Brand: Vulcan-Hart Pages: 27

Brand: Fleetwood Pages: 8

Champion EG-24H

Brand: APW Wyott Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands